Jump to content
SAU Community

Recommended Posts

Looking at doing some sort of heat shielding for my 2 pods that are just sitting there sucking hot air at the moment but wondering what to do about getting some cold air into them afterwards.

My gtst was easy as it already had a nice 3" hole from factory right where I wanted it.

My question is it safe to cut a 3" or so hole right below were the pods are then I could do the induction easily, just ive heard something about how it makes all the support weaker on that side etc etc. It probably wont be so obvious just looking at it from the engine bay.

Only other option I can think of is the headlight replacement but I want it for street use so that would be no good.

Link to comment
https://www.sau.com.au/forums/topic/65156-cai-on-33gtr/
Share on other sites

It has the stock airbox, but who knows what in it or if the box is modified?

LW.

OK I'll go another route.

Stock air box, Piper cross panel filter, custom stainless pipe to replace stock rubber one between turbo/s and AFM.

maybe ask Sydney Kid the max power he has seen from that set up on a GTR.

Honestly, when I had my GTST (R32) and had a pod filter, the thing was only producing like 155rwkw and the engine bay was so hot, the intake temps were like in the 60's during sydney traffic.

so imagine the engine bay of a gtr with 2 turbo's producing obviously more power.

and 2 pods taking up the same room.

even hotter air there for sure.

the stock air box is good.

Link to comment
https://www.sau.com.au/forums/topic/65156-cai-on-33gtr/#findComment-1222333
Share on other sites

GTST: I am aware of Gary's view on Pipercross filters: in fact I will be putting one in the (stock) airbox of my R32 GT-R very shortly.

My point was more that although the Mines R34 may have the "stock airbox", for all we know its been completely changed on the inside. I'm not sure it makes a particularly good point of comparison given all the unknowns surrounding the car.

LW.

Link to comment
https://www.sau.com.au/forums/topic/65156-cai-on-33gtr/#findComment-1222395
Share on other sites

LW - I was just trying to make the point of the stock GTR air box with a panel filter is going to be a better option that PODS in the engine bay.

AND it is cheaper to buy a stock air box and new panel filter, than it is to buy an aftermarket heat shield/air box which probably still uses tha factory snorkel.. to shield off the dirty used pods that would have come with the car from japan.

you will be able to produce the same power (possibly more) if using stock turbo's and maybe even with after market turbo's..

the cost of buying a stock airbox and panel filter is going to be cheaper than buying a heat shield for sure. and give a better result.

Link to comment
https://www.sau.com.au/forums/topic/65156-cai-on-33gtr/#findComment-1222437
Share on other sites

My question is it safe to cut a 3" or so hole right below were the pods are then I could do the induction easily, just ive heard something about how it makes all the support weaker on that side etc etc. It probably wont be so obvious just looking at it from the engine bay.

To answer your original question I drilled a 3" hole below my rear pod. I don't see how it has any effect on the structural integrity on that side. I have two 3" flexible hoses in the front bar. One running through the hole to my rear pod, the other through a factory whole under the headlight to my front pod.

Hope that helps.

Gary.

Link to comment
https://www.sau.com.au/forums/topic/65156-cai-on-33gtr/#findComment-1224680
Share on other sites

theres a factory 3" hole under your front pod? ah thats right yours is 32 so probably different.

You reckon 1 3" hole would be enough for the 2 pods? dont really want to cut 2 holes. Might cut 1 hole and put a scoop intake on also (hope it doesnt look ricey :Oops: )

Link to comment
https://www.sau.com.au/forums/topic/65156-cai-on-33gtr/#findComment-1224876
Share on other sites

The factory hole is under my headlight and was used for part of the air box setup that went to a resonator box. I thought the 33's would have had it too but I could be wrong. It is more like a rectangle hole next to the carbon canister. One big hole is probably enough though.

Link to comment
https://www.sau.com.au/forums/topic/65156-cai-on-33gtr/#findComment-1225169
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • 21 is explicitly the coils detected as the issue. Is it guaranteed the actual issue? No. Just the ECU thinks it is. When you say rattling, describe it better, get an audio clip as best you can if possible.
    • Yea got me coppers. Bad news is I just put them in and the car still has the light and shakes. I also noticed I hear like rattling coming from the exhaust piping right under me. Does 21 also have a possibility of being O2 sensors?   So, coil packs are good, the harness is good, the MAF is working, and obviously the spark plugs just replaced and working.
    • Make sure you drop the GTT base tune back in, and set your injectors again, this will remove anything playing up with it you may have removed. Possibly lean there as it's normally a fast transient going THROUGH atmospheric pressure, and a turbo motor would then quickly go richer as boost builds. The only worry you MIGHT have is ignition timing, as the DE is higher compression than the DET from memory. But again, you're not in boost, so the DE motor will be a lot more forgiving at atmospheric.   Get Murray, Kinkstahs, and Johnny's input on tuning haltechs, those guys have played with tuning enough in the past to be able to help now you're past the trouble shooting stage of the MAP issue
    • @Rusty NutshI mate. Do you have a pinout diagram for the na neo auto ecu? 
    • Yeah thats the plan now. 🤞
×
×
  • Create New...