Jump to content
SAU Community

Wolf3D V4 tuners ? who do u reccomend ?


Recommended Posts

I gave up tring to find someone who was confident to tune mine R33

So I sold it, and just fitted a Power FC like all the other cows in the heard.

Try mercury motorsport, they have done a few.

hey thanks darren...will check that one out...but i dont think he has a dyno though.. that's where nathan took his to tune his EMS on the startlet...but will check that one.

i was hoping Mercury would be able to tune them...i was wondering if they have all programs needed or i still need to bring mine that comes with it ?

thanks for all the help guys....it seems like only a few people here uses Wolf 3d hey ?

I'll give another vote for Matty Spry at PITS. He's good, and damn reasonable too. I was only charged for 2 hours of tuning (at a discounted rate anyway) when he'd spent over 6 hours on it without being able to get a good result power wise. Turns out another company had buggered something up, so it wasnt even his fault but he still only charged for a very reasonable price.

Put it this way, I opened my wallet and pulled out money to pay 4 times what he ended up charging... I was pretty chuffed :)

Also the reason PowerFC is more popular than Wolf3Dv4 is that PowerFC is much better at copying the stock ECU for things like idle-up with A/C and headlights, climate control unit, etc. Wolf has better options for things like outputs and inputs of various devices, including (I believe) MAP sensors. PowerFC makes another version (Called the PowerFC Pro or something?) which is just a PowerFC with the ability to run a MAP sensor instead of the MAF sensor.

Yep he can definately do the Wolf... A mate on here had his done there... He is located on the Gold Coast... Ring him for the address...

Matty has been tuning for a looooong time... Previously from Chiptorque... I've seen him work some wonders...

Yep he can definately do the Wolf...  A mate on here had his done there...  He is located on the Gold Coast...  Ring him for the address...

 

Matty has been tuning for a looooong time...  Previously from Chiptorque...  I've seen him work some wonders...

Hes not too bad, hell if he can fix Andrews car!!!

I wasnt sure he could do wolf, but that confirms that he can. At least give the guy a ring. Techincally tho, all of the systems are much of a muchness, if hes good at one, hes going to be good at another, its just if there is a problem somewhere is when things get slightly trickyer trying to find out what special feature to use to fix the problem.

With the popularity thingy tho, the wolf V3 wasnt so popular, now the V4 is out they seem to be doing a lot better, especially as they now have the plug in (like pfc) version, it seems its a really big insentive, really it means no one can bugger up the wiring, unless it was already like that.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...