Jump to content
SAU Community

Recommended Posts

I currentyly have a series 1 rb25det in a 32 at the moment and i am doing an engine change on this and thinking of putting a rb25det series 2 engine from a 97 skyline.

I have mixed respones and mixed reactions from people on the forums and mechanics. Some say that you can put a Series 2 engine onto a Series 1 wiring loom/harness.

Can anyone confirm that this can be done otherwise i will need to source out a series 2 wiring loom/harness.

Is there any difference in the word wiring loom and wiring harness, different people use different words.

Can i series 1 wiring loom support a series 2 engine?

(Thinking the problem will be the coil packs since the wires on the series 1 go into the back of the engine where on series 2 there is a wire for each injectorm, is this correct?)

Any comments or help on this would be benefitical.

Cheers

harness is different as the series 1 has the little black box up the back... cant remember the name of it. ITs a sprak amplifier or something

Series 2 motor has the amplifier thingy on the actual coil packs themselves

which is totally different

yeah i realised that was the difference, i have heard that instead of connecting the plug to that little box up the back, you can run the 6 wires directly into the coil packs themselves?

Anyone tried this?

the coil pack wiring from the s1 unplugs and just plug in the s2 coil loom.

hrmm interesting....

I have a s1 motor and loom and recently purchased splitfire s2 coils.

The coil plugs on the s1 loom dont fit onto the s2 coils so i need to use s2 plugs instead. I also need to remove the ignitor (black box at the back) and wire the wires into the coil loom.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
×
×
  • Create New...