Jump to content
SAU Community

SAU CABRA, Dinner @ St johns bowling club 2/12/02


Recommended Posts

  • Replies 64
  • Created
  • Last Reply

Top Posters In This Topic

Originally posted by DR GTR

**** yeah I will be there. 7 bucks for the best steak ever! DAMN!

DAVE YOU MUST COME!!!!

I wil try to get Paul and Hustlr too. Paull should have his car tomorrow morning!(monday)

yayayayyayayya i will be cruisign all day..will try to get as much of tommoroow off as i can :)

Me and Loz will be there. And the time is set at around 6-6:30? and dave if you wanted get to the city and me and loz can pick you up if someone isnt going to get you.

Also are we going to be doing anything after :);) And if so please i ask NO TURNING after the nasho i say NO to turns lol.

Oh and how many people do we have? and is there SAFE parking and enough for a few cars? i havent been to this place so thats why im asking.

Ash.

haaha was a good nite besides almost turning 5 skylines into 1

along woodville rd..... and also minh and i almost getting run

off the road by a truck.... was still a good nite....

cereal and torana.. was good to meet u... btw.. how heavy is

u'r car torana.. and how much does it put out?

Originally posted by DON91E

Thanks fellas!!!

Had a freeqin blast! :D

heheheh

Minhderella! !!! hahahahaha

:lol:  

And yes i know wat day sunday is now!!

jsut fort i post it first b4 u guys screw the truth :D  

hahahaha,  

Thanx again fellas!!

hahahaha Donnie had problems lastnight..




  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...