Jump to content
SAU Community

Recommended Posts

Hey ,

It's time to part from my 180sx. I really just want a trade at the moment but if I get a good offer on it then I would possibly sell it.

Looking for a straight swap with or without cash adjustments.

interested in r32, gtir, any jap and turbo car just let me know..

Details:

Model:

1994 180sx with black top engine

approx. 92000 k's

Exterior:

White with black roof

vertex front bar

fat unknown jap side skirts

jet speed rear lip

wing less boot (holes welded up)

type x 15 inch wheels powder coated in white

Engine:

t28bb from s15

fmic with custom piping f

Blitz BOV

pod filter with alloy piping

walbro fuel pump

oil catch can

Blitz DSBC

full kakimota exhaust with a bee R muffler, high flow cat and dump+ front pipe

Handling:

tanabe coil overs height and damper adjustable also camber adjustable

generic jap front and rear strut braces

interior:

1 drivers side recaro

momo stearing wheel

momo gear knob

speco boost gauge

sony head unit with pioneer speakers..

At the moment there's a tear in the recaro a ding in the right hand front quarter panel, few marks here and there.

The front right quarter panel will be replaced but the seat is sold as is.

Any questions please dont hesitate to ask..

Pics wil be up tomorrow

Thanks Pete.

LOCATION: SYDNEY!!

Link to comment
https://www.sau.com.au/forums/topic/68320-trade-eoi-180sx-for-a-r32/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...