Jump to content
SAU Community

Recommended Posts

An interesting read...

http://www.importbuilders.com/pistoncomparo.html

I went with wiseco as they appear to be quite common and proven in the rb30's.

It also made a big difference that my engine builder swore by them. lol

They also happen to be one of the lightest pistons.

But that said.. Wiseco and Arias are both very good pistons.

CP's and some of these others are also apparently good, I've personally heard on set of CP's that were very noisy in a CA18DET.

My engine builder uses these alot, on many different street & race prepped 4-&6cyl cars (including Skylines). I did a little research on these, didn't find anything to worry about.

2BNVS - My builder got these in Lilydale, Victoria. He paid $1100.00. I did a search in Google & and there is heaps of info on them & they should be available in NSW.

I was all for the Arias, cost wasn't really an issue, as they simular in price, but I was convinced by my engineer (had a first hand look at some of the engines he has built) & by a few people using these pistons & who had their engines built at the same place. Let's hope I made the right choice.

CP's and some of these others are also apparently good, I've personally heard on set of CP's that were very noisy in a CA18DET.

Mahle are pretty good pistons, as long as you get the clearances to the spec sheet provided everything will be fine.

CP's are very fine pistons, they require little clearances (much less than Arias or Venolia). Due to the low expansion/clearances required, if they were put in a motor and spec'd to "normal" forged pistons you'll have excessive gaps, and probably get a bit of piston slap.. as well as blow by and wear. I'd be pretty concerned/annoyed if I was the owner of that CA18.

I'd be pretty concerned/annoyed if I was the owner of that CA18.

Interestering you say that.

The builder is apparently the 'best' RB builder in SA, When choosing a builder for mine I threw a few questions at him and honestly had my doubts. So I went to some one else. :(

id stick with well known stuff for anything relating to a motor thats getting a forged bottom end.

no pint risking to save a few $$ and then be stumped later.

Arias all the way

Mahle is a lot better known around the world then Arias mate, thank Porsche for that. Infact Arias are probably cheaper.

Mahle is a lot better known around the world then Arias mate, thank Porsche for that.  Infact Arias are probably cheaper.

i was reffering to use in Skylines.

each piston would be different for the respective motor.

many RB's run arias

6 out of 10 Formula 1 teams use Mahle pistons. Thats a fair indication of their quality. Mahle is one of the worlds biggest piston manufacturers and supply F1, IRL, Nascar, WRC, V8 supercars etc.. as well as Mercedes, BMW, Porsche, Ferrari, GM, Ford etc.. They also own Cosworth Technology and ACL piston products.

They are a little dearer than most other pistons but quality costs money. Look at their F1 pistons, 19 500RPM, 15 000G when they change direction at that RPM and they stay together, thats a fair indication that they have it right.

Attached is a pic of their box-n-box design.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
×
×
  • Create New...