Jump to content
SAU Community

Recommended Posts

Hi guys I have a T3/T4B 400hp turbo for sale its brand new and has never been fitted to a car. It has all garrett internals eg. shaft, turbines, housings etc. It also comes with a 10lbs adjustable internal wastegate and uses a T3 flange so is a good bolt on for the nissan skylines and Vl's and anything with a T3 flange. The turbo is water and oil cooled.

Compressor housing: .60ar

Turbine housing: .48ar

Trim: 54

For any questions you are better off to email me at [email protected] or pm me.

Im asking $900 with the internal gate & delivered will post to anywhere in AUS.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/70791-t3t04b-400hp-garrett/
Share on other sites

Does it use the standard exhaust manifold to bolt on to?  or do you need to have a new one made up?

Yes this turbo will bolt on to the standard exhasut manifold of any car which uses a T3 exhasut flange eg. skylines RB20/25/30

Yes this turbo will bolt on to the standard exhasut manifold of any car which uses a T3 exhasut flange eg. skylines RB20/25/30

What gains at the rear wheels would i be lookin at? only prob is im still running standard ecu standard injectors. i'm guessing not much.

Hi guys I have a T3/T4B 400hp turbo for sale its brand new and has never been fitted to a car. It has all garrett internals eg. shaft, turbines, housings etc. It also comes with a 10lbs adjustable internal wastegate and uses a T3 flange so is a good bolt on for the nissan skylines and Vl's and anything with a T3 flange. The turbo is water and oil cooled.  

Compressor housing: .60ar

Turbine housing: .48ar

Trim: 54

For any questions you are better off to email me at [email protected] or pm me.

Im asking $900 with the internal gate & delivered will post to anywhere in AUS.

Thanks

pm sent.

What gains at the rear wheels would i be lookin at?  only prob is im still running standard ecu standard injectors.  i'm guessing not much.

I wouldnt even try run anything more then stock boost if I had this on my car with stock ecu and injectors, I have a mate who I sold the same turbo to his got a R32 RB20DET with FMIC, GTR fuel pump, 3" zorst with 3" s/s dump, bigger injectors, tunned ECU was dynoed at 225wrkw @ 16psi

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
×
×
  • Create New...