Jump to content
SAU Community

Recommended Posts

u need to yake the car over the pits for an inspection and then u can get WA plates issued if it passes ok, costs around $50 for an inspection then around $15 for new plates, and you'll also have to pay licencing fees too at that time which will prob be around $230 for 6 months, im pretty sure if the car was in your name in Tassie u wont have to pay stamp duty only transfer which shouldnt be too much,

hope that helps :(;):)

Link to comment
https://www.sau.com.au/forums/topic/72263-rego-swap-over/#findComment-1329991
Share on other sites

do u have to rip the wing off and stuff? and we have guages all over the passenger dash and on the drivers door panel bit. When we got caught be the cops in perth he said we need permits for everything? is it just easier to take it all off to go over the pits?

Link to comment
https://www.sau.com.au/forums/topic/72263-rego-swap-over/#findComment-1330491
Share on other sites

I just transferred qld plates to wa a cpl months ago on the car i bought... the first reply above ^^^ has it right... but just in case the car wasnt already in your name (ie. u bought it from someone and it has tassie plates) then a couple of extra bits of info... as well as all the $ mentioned above you will also need to pay the Stamp Duty before they'll give you new plates.

Also, they dont tell you this and most people end up throwing away the receipt... but you'll also be entitled to a refund from Tassie Licensing of the proportion of Rego left on the Tassie rego. When you hand in your tassie plates you'll get a receipt for them, and the refund will be from that date forward - you need to fill out some forms from Tassie Licensing and attach the receipt and post it off.

As for mods etc - what I did was book an inspection but a few days before went to the inspection centre and just walked in and spoke to the inspector for a couple of mins inbetween inspections. I just said "Hi, getting my plates changed over and doing a first registration in WA inspection on Thursday. It has some mods that were OK in tassie and just wanted to quickly ask what I'll need to take off. Are dash mount gauges etc ok, and what about....." Easy way to avoid them not passing you and paying another fee and re-booking again.

:rolleyes:

Link to comment
https://www.sau.com.au/forums/topic/72263-rego-swap-over/#findComment-1330767
Share on other sites

o wicked...im not as scared now...

thanks guys!!

The car is in our name, has been for 4 months or something so i shouldnt have to pay stamp again.... and the rego is due this month so its probably not worth getting receipts and stuff huh?

thanks heaps...!!

Link to comment
https://www.sau.com.au/forums/topic/72263-rego-swap-over/#findComment-1330930
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • f**king around with the bro
    • Ludenham   44.2 tops day no issues  
    • Then today, I went to visit a man with an r33 hat Peter and Road and Race sorted the alignment. As it is being set up for general track/hillclimbs etc it has a heap of caster (7o), less camber than I am used to (1o front and 2o rear, as the caster looks after that in turns without the braking downsides), 3mm front toe out and 0 toe rear. Will see how that goes and track tyre wear to see if it does need more camber, but adjsustment is also limited with nismo arms and adjustable bushes at only 1 end. It does have a bent inner tie rod on the driver's side front but as it came up within spec I'll just leave that as is. So, that is getting close to my chapter of this story....could of tidy ups then a shakedown in early October before it finds a new home.
    • So, it went to Unigroup for a run in and tune on Friday, everything went (generally) well. In terms of fixes, the engine was good and there were no leaks. It needed plugs (I hadn't checked them because the coil pack cover was on a new engine and I couldn't imagine they weren't new.....but turns out the temporary plugs to just keep it sealed up were in there.....new plugs gapped to 0.8 and it was fine from there. Also, there was a little preload on the clutch slave which caused some slip. I haven't had the box off so I don't know what the clutch looks like; my guess it is brand new and the pedal had not been adjusted....backed that off a bit and it held fine. Last thing will have Dose crying....the idle especially when cold is a bit difficult between the cams, forward plenum, atmo blow off valve and an 80s air management system. It is fine when hot but a little uneven when cold, will see if I can sort or at least improve that one cold morning. Other than that, tuning went fine. It made 245 but was pulled back to 227 which 2 opportunities to improve in future. 1. The factory CAS is not great and was jumping around at high RPM, so Mark took 2 degrees out up top (that is why it stops making power and lost 20kw). Very safe this way and the extra power is available but will require a more modern ECU and better cam (or even better crank) sensor 2. The 2871 in factory housings is very big for a low mount, and the internal wastegate is too small, so it was creeping from mid range all the way to redline....the duty cycle on the boost controller is turned down a little for safety. That is much harder to fix, it would need a large external gate and that would require a whole bunch of other changes, so it will go as it is for now. It feels nice and healthy and safe, so should be good for about a billion laps like this.
    • what sort of caliper are they? If they are a slider and you gave everything a good clean, you might need to regrease the pins. My guess though is they will come good after some abuse as suggested above
×
×
  • Create New...