Jump to content
SAU Community

Recommended Posts

Right then, for the first time in 2 and a half years my car is doing some interesting things.

1. When idling if i put the clutch in and put it in gear, leave my foot on the clutch, the revs increase by like, 300rpm. Then when i take it out of gear but still leave my foot on the clutch, it returns to normal.?????????Doesn't happen all the time though.

2. The worse of the two. While travelling down Orrong? road yesterday, while acceleration the revs dropped to 600 (idling). Then after about a 2 sec delay it came back up to the rpm i'd expect to do at 80kmh. ?????? It did it about 4-5 time in the space of about 10mins. I filled the tank up after work on the way home and it didn't do it again. What the?????????

Any suggestions?

Link to comment
https://www.sau.com.au/forums/topic/72592-idling-accelerating-issues/
Share on other sites

how low was your fuel tank??

May have some non fuel in it - i had this problem with water in fuel in a suburu my father in law owned.

We put a cup of metho in the tank, filled the car with fuel and then we could run it dry . the metho apparently stops the fuel and water seperating - we then ran it out completely never had the problem again.

What mods do you have? the revs picking up at idle sound like they may be the NVCS kicking in. If your idle isnt stable, it 'may' activate it once the neutral switch has been deactivated.

Second problem could have been fuel surging due to not enough in the tank.

More info would be good, mods, settings etc.

NVCS is the system nissan use that advances timing on the intake between 1050 and 4500rpm. If the revs at idle get near 1050, and the car is in gear, the NVCS will activate, advancing the timing and the revs will go up.

To test if this is the problem, just unplug the NVCS and put the car in gear. The NVCS plug is front drivers side of the head and has a brown plug. Or, you could just get someone else to put it in gear while you listed with the hood up - there will be an audible click noise when the NVCS activates.

For only a cat back it shouldnt cause dramas. 1/8 of a tank shouldnt cause dramas either with stock fuel pump.

Oh dear, the problem just got worse. Now when i come to a stop at the light and stuff the car just slowly drops revs and cuts out. It will happen 3 out of 5 times. When the car is stationary the rpm needle is constantly searching on the dial, if that makes sense.;) What the **** is wrong with my car? It seems to me like a computer issue. Like one of the senses has shat it's self and the computer is therefor going ?????? what the?.

Any ideas?

It could be your AAC - that is your idle control solenoid at the back of the plenum. It has a brown plug hanging off it. Check the plug is properly in place, try removing the plug and cleaning the electrical contact with brake cleaner or electrical contact cleaner.

Next step is to remove it and give it a good clean. Three bolts, pretty easy. You will also need to disconnect the purple plug to do this, its the AC idle solenoid. Once removed, give it a bath in brake cleaner.

Another thing to try is keep your ac switched on, as this uses an additional solenoid to bleed extra air into the plenum - may keep you out of trouble for the while. If it helps you will need to keep the aircon turned down to coldest setting so it is on most of the time (climate control will cycle on/off to maintain the set temp).

Another thing that is vital is to check ALL your vacuum hoses, intercooler pipes etc as well. Most skylines are old and the hoses tend to perish and crack.

Hope it helps. Sorry but I am somewhat taking stabs in the dark. Most fault finding is a process of elimination.

G/L

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • LOL.... a good amount of people (not all) on that continent seem to know everything and like to measure things in bananas, football fields, statue of liberties instead of the metric system lol.
    • I assume the modules are similar enough, so if you've had no issues I don't see why I would. I have tried to find a wiring diagram for the FPCM / fuel pump circuit, but I can't find it anywhere. Otherwise, I would just do some wire cutting and joining at the FPCM and give the 12 V supplied to the FPCM directly to the pump instead. If you know anyone that could help with wiring diagrams, I'd be very happy  
    • If it dies, then bypass. The task isn't difficult. I have one running on a standard R32 FPCM. That's after nearly 20 years of it running an 040, which pull substantially more current than the Walbro. They're not the same module, but I'd hope it indicates that the R33 one should be man enough for the job. I think people kill them when putting proper sized pumps on them, not these little toy pumps we're talking about here.
    • Silicone spray won't hurt anything. And if it does, that's an opportunity to put some solid steel spherical bushings in, so you can really learn what suspension noise sounds like, If you're going to try it, just spray one bush at a time, so you can work out which one is actually noisy. My best guess is that if the noise started only since putting the coilovers in, then it is just noise being transmitted up through the top mounts of the struts, and not necessarily "new" noise from bushes. But it's almost impossible to know.
    • Are you saying the 34 is SUV height, and not that we're talking about an SUV here? (because if we're talking about an SUV, you don't fix them. You just replace them when something breaks. Not worth establishing sufficient emotional connection with an SUV to warrant doing any work on one). I wouldn't jack my car up on a short little loop of 10mm steel rod poking out through a hole in the bumper bar, front or rear end. I realise that we're probably not talking about that type of loop at the front, being the one under/behind the bar on a Skyline.... but even for that one, trying to jack up on what amounts to a thin piece of steel, designed purely for withstanding a horizontal tension force, not a vertical compressive force (and so would be prone to buckling/crushing) and, my most particular bitch about it - located RIGHT AT THE EXTREME FRONT OF THE CAR, applying a load up through the radiator support panel, etc, with almost the entire mass of the car cantilevered between there and the rear wheels? Nope. Not doing that. Not on the regular. That structure out there in front of the front crossmember is not designed to carry load in the vertical direction. Not really designed to carry any load at all, really. The chassis rail that the tow point is connected to would be fine loaded in tension, as per towing. Not intended to carry the mass of the whole car, especially loaded all on one rail, with twisting and all sorts of shitty load distribution going on. No, I will happily drive up on some pieces of wood, thanks. That can only happen on driven wheels, and they are at the other end of the car, and this problem does not exist at that end of the car. And even then, I have been known to drive up on at least 1x piece of 2x8 each side at the rear, simply to reduce the amount of jack pumping necessary to get the car up high enough for the jack stands. What really really shits me about Skylines is the lack of decent places for chassis stands at either end of the car. You'd think they'd be designed into the crossmembers.
×
×
  • Create New...