Jump to content
SAU Community

Plex tonight.

Hicks

By Hicks,
in Western Australia

 Share

Recommended Posts

GTS-t VSPEC Grand Master

GTS-t VSPEC

Posted
Posted

Sorry Hicks I'd already posted on the other thread "Wednesday Night Drags". Well for my first go it wasn't too bad but my launch is embarrassing, even V8's took off harder than me, so there's plenty of room for improvement and enough horsepower to get the mid-13's, I'll be there next Wednesday, hope you can make it with your new clutch Hicks.

Best time 13.9, best top speed 170km/hr, best 60' 2.3 (which is shit) and we wont even discuss my reaction time, I must have been asleep on some runs.

But it was great fun and I'm hanging out to improve my times.

See'ya:burnout:

Link to comment
https://www.sau.com.au/forums/topic/7287-plex-tonight/#findComment-107273
Share on other sites
Hicks Mentor

Hicks

Posted
  • Author
Posted

You've got a pretty nice terminal speed though, your just loosing it at the start. But 2.3 60ft isn't that bad, my first 13.8 i had a speed of 2.1, but my 13.7 was a 2.3. And that was during the day!! I think that the track was really grippy though due to the heat.

Link to comment
https://www.sau.com.au/forums/topic/7287-plex-tonight/#findComment-107404
Share on other sites
GTS-t VSPEC Grand Master

GTS-t VSPEC

Posted
Posted

Yeah, everyone keeps telling me, but when I get the stage lights I'm too busy trying to get my revs right that by the time I look up I see it's turned green, then I nail it and loose traction. I think towards the end I was starting to feel more comfortable, it was also cooler, and beginning to get my shit together.

It certainly doesn't look hard as a spectator, but driving is a bit more difficult. I think next week I'll be better prepared and my times should drop, with luck.

Thanks for the tips though.

See'ya:burnout:

Link to comment
https://www.sau.com.au/forums/topic/7287-plex-tonight/#findComment-107515
Share on other sites
GTS-t VSPEC Grand Master

GTS-t VSPEC

Posted
Posted

Steve,

I don't think Wolf has launch control planned, but they are bringing out a firmware update for Anti-lag, so I think the Autronic SM2 is the only one I know with launch control. I have traction control on my car, but I leave this disabled as you end up going slower.

I don't think I need the launch control, I just need more practice. I was also getting alot of diff bounce, so I will try the pineapples to see if that can improve the launch.

See'ya:burnout:

Link to comment
https://www.sau.com.au/forums/topic/7287-plex-tonight/#findComment-107620
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Jarsky
      After market rear camber arm adjustment

      By Jarsky · Posted

      This. A 3d wheel alignment is like $120...just take it to the shop. Since theres probably multiple adjustments that need to be made after changing something. Mine has front/rear lower arms, traction rods, tension rods, camber arms, toe arms, front upper arms, hicas kit, sway bars and coilovers. I measure from the edge of the bolt holes on the originals and set the same length on all the adjustable stuff to dial it as close as I could to OEM. Took it straight for alignment; it didnt feel right at all...after alignment, it feels perfect. Similarly i've just changed the springs on another car; and I still needed multiple adjustments to bring it back in spec.
    • Rezz
      Spotted on the street....

      By Rezz · Posted

      A full Veilside kitted JZA80 Supra in Meriken park in Kobe city a few weeks back
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Its a well known brand in New Zealand; its a rebrand of the Rhino RAV3.  I don't know what the wiring difference *is* between the rev.1 (installed about 15 years ago) and rev.2; but as you say I would think its reasonable that it uses the same immobiliser relay circuits. I had a look but couldnt see a similar harness; but didnt move things around since I didnt want to mess with it   It was one of AVS well known Authorised Installers; I spoke to AVS themselves about it but theyre unsure hence seeking advice more so from the skyline community who are more familiar with the actual car and its wiring. Im in Auckland; but the installer is on the other side of the city so hes very reluctant to come back to even look at it to confirm something isnt connected into the wrong wire.  I dont want to drop the name since they *did* do a really good job for the most part. Everything is very tidy and he fully replaced all the alarm wiring, all the sensors, the wiring to the door motors, installed a switch which was never installed in the first place...really happy with the alarm install itself..just not this one issue. We all make mistakes, if it is the alarm, I just want my fuel pump getting proper switched, fused, power as it was; without having to shell out for an auto electrician to switch a wire and tell me it was the alarm. 
    • pacman_1219
      Blue/grey smoke after idle

      By pacman_1219 · Posted

      Even with the piston at TDC there was room for it to drop, but I don't think it can drop fully into the cylinder, the problem you have is that you need something pushing against the valve to hold it up so you have enough room to put the new stem seal on and the spring etc.  I used compressed air only because putting rope in the cylinder seemed a bit risky to me, I know people have done it countless times before like this. Overall it's a pain in the ass job. Honestly you'd probably be better off taking the head off because the risk of dropping something in the engine and the finicky-ness of it all is very stressful. If you are going to attempt it though i 10000% recommend a 36050 valve spring/keeper tool. I had both the traditional lever type and after doing 1 cylinder it was absolute pain to get those valve keepers in place, even with 2 people. That 36050 is amazing, you do have to push hard to get them in place but it works perfectly almost every time. Back to my actual issue I think my engine is just tired and old and the rings have gone bad. The comp numbers (cold, no oil) were: Cyl 1 -129psi Cyl 2 - 133psi Cyl 3 - 138psi Cyl 4 - 137psi Cyl 5 - 157psi Cyl 6 - 142psi   Cylinder 5 and 6 having the most carbon on them.
    • MBS206
      R33 Fuel Pump & Brakes after alarm swap

      By MBS206 · Posted

      Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
×
×
  • Create New...