Jump to content
SAU Community

Recommended Posts

I would like to run methanol as a fuel as I have seen many cars benefit from the changement. Rayhall turbocharging claims on their website that you can add approx another 15 degrees of timing into your engine which is heeps which changement from pump to methanol! In addition, I have also read that methanol can give you an extra 20 percent power over pump fuel (providing your engine can take it).

Who has experiences with methanol?

Who has seen benefits?

What are the disadvantages apart from needing to changes injectors + pump (due to requirement of twice the normal flow since methanol needs to run twice as rich as petrol alone) and legality?

How much is it and where is it available on the gold coast?

What is its octane rating?

Does anyother fuel compare to methanol for power/dollar?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/74179-methanol-as-a-performance-fuel/
Share on other sites

Methanol is a fuel only ever used in darg cars and the like, it's not legal for road use. If you have ever stood near a car running Methanol you would know why. Apart from that you have to run a completly new fuel setup for it, i don't know specifics but i know of friends in the drag scene that have mentioned it.

If you want to run a better fuel than 98 you would still have to stick with a fuel like VP racing, that's about 103 and it's still unleaded so you can use it on the street. It's about $3.50 per litre though.

Methanol is used in drag set-ups as it will makes ya eyes water from the fumes. The fact is that most methanol set-ups on road cars are not 100% methanol (read this is for the strip only not for street use).

Basically Methanol lowers the intake temps and increases ron levels so more boost can be run without the problems of detonation. The system has to be set up correctly and not just "added to the tank". Its not an octane booster so don't even think of it like that. Most people run an additional injector or two from a fuel cell, separate lines and pump. I have seen a couple set up on N/A and turbo cars and have run effectively assisting in bring down 1/4 times and boosting top end power.

At the end of the day unless you have experience in fitting a system the cost will exceed the benefit. Stick to VP race fuels as listed above if you need increased octane. To reduce inlet temops the CO2 systems work extremely well, I prefer to use only externally on intercoolers as this has worked the best from what I have seen from properly tuned cars!!

I would like to run methanol as a fuel as I have seen many cars benefit from the changement. Rayhall turbocharging claims on their website that you can add approx another 15 degrees of timing into your engine which is heeps which changement from pump to methanol! In addition, I have also read that methanol can give you an extra 20 percent power over pump fuel (providing your engine can take it).  

Who has experiences with methanol?  

Who has seen benefits?  

What are the disadvantages apart from needing to changes injectors + pump (due to requirement of twice the normal flow since methanol needs to run twice as rich as petrol alone) and legality?

How much is it and where is it available on the gold coast?

What is its octane rating?

Does anyother fuel compare to methanol for power/dollar?

Cheers

Methanol does allow you to run more ignition or boost. we ran 35psi on methanol.

Intake air temperatures are very low. Dont have to run intercooler. Fuel is good for racing only. Too fidly for the street, plus it is allegal. Fuel is very corrosive. It attacks everything. have to run serious filter system. Most people will argue that running electric pumps is trouble. i tend to agree, we had trouble with pumps. Mechanical fuel pump is way too go. Make sure your tune is good as methanol is not as forgiving, serious melt downs occur. But if your setup & tune is good, you will see the benefits. Its just a bit of trial & error.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...