Jump to content
SAU Community

Intercooler pipes - what colour???????????????????????????????????????????? ?


Recommended Posts

A radiator is a convective device, colour is irrelevant for convection. Radiation will contribute 2/10 of fark all of the total heat transfer.

can you explain/back that up please???

bit :confused: thats all.

can you explain/back that up please???

bit  :confused: thats all.

The diffence in colour will affect heat changes but only from radiant heat ie sun light.

For ambient heat (hot air) the construction material will have a much higher effect. Materials such as aluminium will absorb 3 times as much heat as steel. If you want to keep the air as cool as possible the best product to use is plastic and it has very little heat density.

Another few factors are contact time and surface area. Because the air is only in contact with the metal for a very short time only a tiny bit of the heat will be transfered to the air. Being round, the piping has the lowest surface area to cross-sectional area of any shape.

If you want to keep the air cool then use plastic with heat wrap as plastic doesn't corrode.

stainless wont give up heat like aluminium will. always use aluminium except when near a heat source. ie exhaust manifold.

even then a heat shield will go a long way to reducing intake pipe temps.

i always paint my pipes matt black. i like the factory look. i even paint my bov and boost controller. you would be surprised that the cops dont see anything that is matt black.

yeah steel doesn't transfre heat very well so it is good to use. Just to goive you an idea. Have you ever picked up a iron/steel frypan? Any aluminium one will cook just aswell because of it's heat distribution properties.

On the other hand non stainless can rust. So go stainless.

Seriously, I think this is being over analysed waaay too much.

*Significant factors in the choice of material are:

Corrosion resistance (aesthetics), ease of fabrication, cost, availability

*Significant factors in the choice of colour/surface finish are:

Aesthetics

*Minor factors (IMO not worth worrying about) in the choice of material and colour/surface finish are:

Heat transfer, emissivity

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...