Jump to content
SAU Community

Recommended Posts

Wanted to preferably borrow/hire, but may buy these STOCK items. Need them to get the car through compliance. I am in Adelaide, but can pay for shipping. There must be tons of this near worthless gear around the place :D

Thanks!

awesome - the sooner I can get it the better. How many km has it done, and how much do you want for it Bob?

Anyone else got these bits?

93k

price hmm $100? To make it worth my while packaging it up.

You might find something local. I will look into putting the bilsteins I have in my spare room on and get back to you.

cool, sounds good! I guess transport is the next problem .... I might do some research. I am in Adelaide if you didn't know :)

You don't still have your stock exhaust too by any chance do you?

cool - I take it the shocks/springs are in good condition (not leaking or anything), as I need them to get through a compliance and government inspection.

Great mate, I'll take them for sure (assuming they are in ok condition).

How much did you get for the exhaust (as a price guide)?

Cheers, let me know the second they are off the car - apparently my car has already left Japan, so my car is only a few weeks off. I can dd you the money as soon as they are ready to send!

Anyone else got an exhaust/know where I could find one?

Ok then. One of the rear ones leaked before I got it but you can tell the leaking has stopped cos it's all dry so when they have been cleaned you'll never know. I'm not saying in any way that the shocks are in great condition, just that they look fine and go ok.

You wont have any problems with inspections.

I'll pm you when I get it off.

not that I care (since they are only going to be in for compliance then my aftermarket ones will be going in), but how many km had your car done when you got it, and have you noticed them sagging in height at all, or not being as firm as original? Reason I ask is because I have an S15 that I bought brand new, and at around 50,000km I noticed the rear had dropped about an inch and they certainly roll more going around corners.

  • 2 weeks later...

thanks Bob, sorry to bug you in my PMs ;) - I am just very keen to get this baby on the road! Let me know the second they are off the car please :)

ANYONE have a stock R34 4 door exhaust??? Or know where I could track one down. Does anyone have a friend with an R34GTT 4 door that might have a stock exhaust in their shed? Thanks in advance!

Andrew

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...