Jump to content
SAU Community

Recommended Posts

***NEW*** Japanese quality engineered cooler kits for most models. ***NEW***

S13, PS13, RPS13, S14, S15.

HCR32, ECR33, ER34.

HKS Type-S

301x600x65mm

$1450 with free delivery

gYQ63317.jpg

R33 GTS-T RB25 model shown

TRUST V-SPL

276x600x76mm

$1450 with free delivery

kVq63469.jpg

S13 model shown

TRUST R-SPL

294x600x115mm

$2350 with free delivery

BLITZ LM

$1450 with free delivery

Are these actually Real not take offs i need one for my rb25 wich will need to be able to support 250-300rwkw! got any in mind?

cheers

These are the genuine item shipped directly from Japan.

I do have a cooler in mind for you. You're looking for a cooler which accomodates up around 450-500ps.

Stay tuned.

Are these actually Real not take offs i need one for my rb25 wich will need to be able to support 250-300rwkw! got any in mind?

cheers

The kits listed above are the only kits we bring into the country at this stage. Any specific orders may take time to locate at a desirable price for the consumer.

Charles.

Sometimes on the R33 the piping goes left then up , or then there is the 180degree bend going back towards the stock intercooler position. Which way is it? Hybrid style or 180degree bend style.

correction..

only Apexi that i know of has this bend.

perhaps somebody else here may be able to assist.

all of the kits i can bring in do NOT have the 180 degree bend on one side for the RB25DET.

not these particular sets.

also, HPI do a FMIC kits for all nissan makes. once again, straight out the side of the tank rather than the 180 degree bend on the end of the tank.

can get these in also for about $1600 landed.



  • Similar Content

  • Latest Posts

    • bumping this post as im still having dramas, my fuel pick up is sitting on the bottom of the tank, my pump gets a constant 13 volts through a relay, my fuel pressure holds consistently without fluttering or dropping, yet as soon as im near half a tank of fuel my car starts fuel starving and leaning out, it cant be due to g force as it never pulls hard enough before it starts breaking up, any help would be much appreciated 
    • Just a thought, was that car and auto at any point of its life? If so, maybe whoever bridged the inhibitor switch/circuit did a not so good job.
    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
×
×
  • Create New...