Jump to content
SAU Community

Recommended Posts

Only have 2 of them - really like them but doesnt really write on the back what they are.

All it writes on the front is A-tech Monoblock or something. Searched around but couldnt find out.

Hopefully someone here will know.

Ohh yeah, talking about the wheels on the front : )

Thanks.

Husnu (Hus).

Link to comment
https://www.sau.com.au/forums/topic/78031-what-wheels-are-these/
Share on other sites

They look the same as the ones I've got on my 32. If they are, they are A-Tech Monoblock Forged Alloys that have a sticker on them saying "Final Speed"

I know more about the wheels if you need to / want to know.

What's the go ? Do you just want to know what they are or are you looking to sell them or .....??

They look the same as the ones I've got on my 32. If they are, they are A-Tech Monoblock Forged Alloys that have a sticker on them saying "Final Speed"

I know more about the wheels if you need to / want to know.

What's the go ? Do you just want to know what they are or are you looking to sell them or .....??

I think we might be getting somewhere. I only have the front pair. I need to find another 2 to make it a set. The ones I have are 17x9JJ

If I can find atleast 9JJ for the rears it would be good. If not, i might have to settle for 8-8.5JJ and shift the 9JJ to the rear.

I like the wheels, no good having only 2 of them. If you know where I can get them it would be great. In the mean time, i'll try and hunt them down in Japan.

Thanks a lot.

Hus.

I'd say those ones are the next generation of the ones I have as they state "Semi Solid Forged" where as mine say "Monoblock Forged Alloy" and mine do not have the red word "forged" on the sticker but hey, they look the goods. :rofl:

Selling price here is Aus was ( don't see them being sold new in Aus anymore ) around $400 - $450 per wheel.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...