Jump to content
SAU Community

KILLER-T needs help


Recommended Posts

Adam,

The malpassi is pretty easy to setup. Have you got a fuel pressure guage yet to go with it? You should get one if you haven't. You can then set a base fuel pressure and hook it all up yourself, drive to the tuner and spend very little time mucking about (less $$$).

Whatisname, has the malpassi and similar power. He would have a base pressure close to what you would need.

The AFM plug is different on the Z32. Hope you got the Z32 plug with the afm you could use it by slicing into the original afm wires.

KillerT,

I have a malpassi regulator on mine, I'd be more than happy to come over so you can copy what they did with mine, although I do have a diiferent manifold, but that shouldn't make a difference.

As far as the Z32 goes, if you have a plug that fits into the Z32 then I'm sure I can figure out what the correct pinout's are to join it to your existing loom.

PM me if you need my help.

See'ya:burnout:

Guest KILLER-T

Ok i got the Z32 afm in it was easy after looking at a few wiring diag's if anyone wants to know what each wire is on their afm is

black / white = 12v

white / blue = ecu earth

black = earth

orange / blue = signal wire

This is for s1 r33 gts25t's only s2 are not the same

and GTSVspec i might take u up on that offer so i can see how your fuel reg is set up

:)

Err forgive me if I missed something KillerT but are you changing the computer to suit the different voltage scale deflection you will get ?

I always thought that this mod only worked with aftermarket computer and only reqd for big HP engines

Ken

Guest KILLER-T
Originally posted by gtrken

Err forgive me if I missed something KillerT but are you changing the computer to suit the different voltage scale deflection you will get ?

I always thought that this mod only worked with aftermarket computer and only reqd for big HP engines

Ken

you are forgiven Ken the mod list on my car is getting longer than my arm it seems to be one thing after another sofar the car has

Power fc

AVCR

Big cooler

stainless dump

hi flow cat

twin system from cat back

bigger turbo

rebuilt engine wiseco forged pistons

bosch fuel pump

Z32afm

malpassi fuel reg

I needed the z32amf because the stock item was maxed out @1bar and this is fixed now it took it for a quick squirt down roe hwy 1.2bar and the afm was only at 4v :)

Steve,

As Killer-T discovered the wiring is not very difficult, it has an additional ground for the signal, to prevent noise on the signal and floating voltages. It should only take about 30mins to do it yourself, just make sure you have a soldering iron.

Killer-T,

If you already have the regulator then you may aswell do all the lines aswell, it not difficult and you can work out where they go straight from mine.

See'ya:burnout:

Guest KILLER-T

Yes dude i have a soldering iron but looking for the damm thing today took me about 1 hour to find it man i got to clean my shed out plus the time it took me to work out the wires so it took me the good part of the day to do this job. But if you knew what you were doing and didnt have to spend a hour looking for your soldering iron you could do it in 15 min

This is what I got from Lumpy,

"For the Z afm, the following pins are what we need.

Pin 2 - Power

Pin 3 - Ground

Pin 5 - Signal

The connector is actually a 6 pin plug.

Looking from the wire side, with 2 locating tabs at the top, and 3 at the bottom, pin 6 is on the left, pin 1 at the right."

Is that in line with what you used Killer-T?

Also, out of interest, is putting in forgies very expensive, or did you do it yourself?

Cheers

Steve

Guest KILLER-T

No i had 4 wires on my factory plug and a 5th space on the plug that was not used looking at the wire side of the factory plug

pin one black with white stripe = power

pin two white with blue stripe =ground

pin tree black = ground

pin four orange with blue stripe = signal wire

and the pistons cost around 1500 and there is no way i am clued up enough to pull my engine down i got Criss Mills to do the rebuild it was around 5500 all up inc machining and a mild port and polish

Guest KILLER-T

Last dyno run we could not tune the cars top end properly because of the stock afm running out after 1 bar and i had the rev limiter set at 6500rpm because it didnt want to hurt my new engine and yes i know im a soft **** for setting the limit to 6500 but it still managed to pull 305 rwhp on psi's dyno .I have no idea what it will pull now that i have this new afm and fuel reg and a new rev limit of 7000 rpm i will gt it tuned to run 1.2bar that should give the engine a bit more punch :burnout: :burnout:

I wired a Z32 afm in my 32 and basically just left the first wire A (orange ) on the z32 and then wired the other 4 in order, eg pin b on z32 to pin a on the stock plug. Everything runs fine so it must be ok.

32s and 33 are the same i think.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...