Jump to content
SAU Community

Recommended Posts

i was installing a sub and amp today

i think i did everything right.

power cable earth cable etc etc.

the amps got power and all but no sound is coming out.

seems like the amps dead

i checked the wiring on the remote line and it seems to be ok.

what could the problem be??

Link to comment
https://www.sau.com.au/forums/topic/80583-the-amps-got-power-but-no-sound/
Share on other sites

real stupid thing but if it a DVC sub make sure both your coils are wired the right way(both neg-neg pos-pos). I know it's a really dumb thing to say but i've seen it happen in the past. save that does your head unit have switchable rca jacks? some are switchable for amp out/aux in.

How do you know the amp is on? I'm assuming the light is on.

You should check the remote line with a test light to make sure current is running through it, although if the amp has a light this won't be an issue 'cos if it's on the light will be on.

If there is no light then a quick way of testing is shorting the power and the remote (so your power cable runs to your power on the amp, then just get a small wire and short the remote and power terminals on the amp).

Check the fade and balance on your head unit to make sure it's actually giving output to the amp. Check where you plugged the RCAs into the head unit to make sure you've used the correct output. If for example your headunit has a sub woofer output and you haven't enabled the sub then nothing will be outputted from those RCAs.

Check you've plugged the RCAs into the proper input on the amp, some can have more than one input so make sure if you've got more than one that the speakers/sub are/is actually plugged into the same channel.

Finally if you're bridging, enable the bridge mode if your amp has a button for it. Otherwise if you're not bridging make sure the bridge mode is off, if your amp has a button for it.

Check the wires on your amp to your speakers are correctly wired to the speaker, so the positive goes to positive and the negative goes to negative. Also make sure it's plugged into the proper wiring bank - sometimes it can get confusing there.

Good luck. Let us know how you go.

hm..

i may have found the problem

seems like the RCA output needs to be turned on??

but i dunno how to turn it on

cant find anything from the HU that seems to control it

those damn japanese HU

i think i might as well get a new HU

try turning it off, and holding each button down for a few seconds as a start. pioneers at least have a settings menu that you access by turning off and holding a specific button for a few secs. That's if you dont really want to buy a new HU anyway :(

i had the same prob with mine ... got the shits really bad ... i thought i f****d something but after a quick read through all of my manuals i solved the prob!!!

find out what h/u you have 1st then do a google search to see if there is support befor eyou toss it for a new one!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...