Jump to content
SAU Community

Recommended Posts

Hey folks,

I'm suffering from a terribly annoying noise coming from the alternator. It's been there ever since I bought the skyline. I believe that this can happen when you have your input wires too close to power cables. So, I went and bought one of those noise cancelling things from jaycar and I was told to put this between the alternator and the battery, closest to the battery side.

I'm driving a series I R33 ('93) and the battery is in the boot. The only wire connected to the +ve side of the battery comes from the box next to it.

My question is this: Where should I be putting this device in?

At the moment I have it wired between battery and fuses, going into the amps, but it doesn't really do anything. I tried putting it in between the battery and this little box thing next to it, but the car didn't even start, so that quickly changed....

(In case I've confused anyone with what "noise cancelling device" I'm talking about, it's a cylindrical shaped thing with a positive cable coming out each end and a negative wire coming out one side. I'm told that that it doesn't matter with direction it's facing when wired, as long as it is grounded.)

If anyone can help me out with this it would be greatly appreciated - even though I can't hear the whinning with loud music, when it's down low it drives me up the wall!

Thanks in advance!

Link to comment
https://www.sau.com.au/forums/topic/81467-where-is-alternator-wire/
Share on other sites

The noise I get is in every gear. I hadn't really thought of putting it under the bonnet. I think I remembered the guy in jaycar saying to go as close to the battery as possible. If I had the choice I'd rather install it in the boot rather than in the engine bay. If need be I guess I could put it up front.

Anyone got any further ideas or info?

  • 3 weeks later...
  • 1 year later...

Thought i would ask in here instead of starting another new post..... already asked the question ova in forced induction but havent got an answer as yet though i might have put it in the wrong place...

anyway here is a link to my question

http://www.skylinesaustralia.com/forums/in...howtopic=133670

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hang on. Let me get this straight. The desire is to have coilovers, BC in particular, to be MORE comfortable on Sydney roads than stock suspension? Well, that's obviously not right. BCs have crude damping design at the very best, and typically hard spring rates. BC stands for Billy Cart. And then, the desire is to put in some shitty old worn out stockers, to get it blue slipped and then put the BCs back in? And then.....what? Not worry about getting pulled up by the Plod? Because you seem to have raised a worry about paying for engineering (which actually does solve all your legality problems) and still getting pulled up.... but the only problem there is that if/when that happens you have to show your paperwork at the inspection station. Whereas, if you just swap in borrowed shitty old stockers to get it slipped now, and then you get defected in the future, you have to go find more shitty old stockers then too. You course of action looks like this set of options: Buy brand new stock type dampers, and springs. probably cost a bit more than $1k all up, but will last for the remaining life of the car. Put them in, pass inspection, drive on them forever more. Hell, they could even be really nice Bilsteins and Kings or other lower&stiffer springs if you wanted. Get the car engineered as is. ~$1k. Buy new Shockworks coilvers (or MCA) and also pay for engineering. You're spending a lot more here. But these will be the best things that you could drive around on.
    • Might be worthwhile hitting up Facebook's groups, I know most of them contain terrible people and scammers - however you might be able to find someone that's in Sydney with factory suspension you could purchase and/or hire. Just do not send any form of money anywhere, in person cash only.
    • Thanks @Duncan Ride height is fine. I think it's almost stock tbh. Happy to share a pic. I don't actually have a regular mechanic as haven't lived in Sydney too long. Could you or anyone recommend any shops in Sydney?
    • You just need a different blue slip shop (preferably one you regularly use as a mechanic), and make sure the coil overs are as close as possible to standard height
    • yeah the sugar refining companies were pushing for the same in Oz originally, all fuels were going to have 10% ethanol to make them "cheaper" (noting, that the loss in l/100 might be greater than the decrease in price). I guess they won that fight in Canadia
×
×
  • Create New...