Jump to content
SAU Community

Running A Straight Through Exhaust On My Skyline ?

SirSkyline

By SirSkyline,
in General Maintenance

 Share

Recommended Posts

SirSkyline Experienced

SirSkyline

Posted
Posted

If I put a straight through exhaust on my pretty much stock R33 Skyline for track days will this hurt anything ?? there will no cat and muffler.

Can someone tell me the advantages and disadvantages of this

Cheers

SirSkyline

Ska Grand Master

Ska

Posted
Posted

I ran a straight through zaust on my old r33, only had 4 bends in the whole thing (1 turbo down, 2 bend to flat, 3 just past the cat(which was gutted), 4 just a small bend to get around the rear diff) and what I thought was a muffler was actually a bit of stainless steel welded around the pipe to make it look like a muffler.

Was VERY loud, apparently, well it was not drony or loud in the cabin.... :(

Anyway ran 7psi fine and ran 12psi with fmic fine, for 18mths.

Ska Grand Master

Ska

Posted
Posted

Nope but I did have a SAFC installed and tuned.

Personally I would actually drop the cat and cat back off if I was going to the track, or go to any good exhaust shop and get them to make a small pipe with a bend it it to shoot the fumes out the side of the car and bolt it up to where the cat usually goes, then you'll get some noise!!!

Of course if you then decided to drive this on the road and get caught you would be in VERY big trouble, sounds absolutly hella good though! Revhead on here has a small pipe which he fits to his R33 with a PowerFC for track days, with his hybrid t3/t4 turbo, all you hear is that sweet high pitch whislte of boost once it comes on!

Ska Grand Master

Ska

Posted
Posted

Oh and when I was running totally stock I dyno'd 132rwkw, then just after putting a cat back zaust on, no other changes, 2 weeks later at the same dyno I got 147rwkw.

Just goes to show just how much power can be gained by using the right exhaust system.

In the end with my pipe, pod, fmic, bleed valve set to 10psi and SAFC I got 177rwkw, not bad considering I started off with 132rwkw.

SirSkyline Experienced

SirSkyline

Posted
  • Author
Posted
woldnt you be shooting flames though  :P

I guess you could get away with it if indeed you we able to do it discretely. However, it would be one loud car as you have discovered.

I would not be complaining one bit if it does shot flames. B) I might put a cat on it after the track day and see how we go for a while

Nozila Grand Master

Nozila

Posted
Posted

I remember a while back when I installed my dump pipe that I accidently left a slight gap between the manifold that connected the turbo and dump. Result? the most awesome sounding noise from an RB engine, an added bonus was that is so friggn fast as well. Sorry, bit off topic. hehe

Ska Grand Master

Ska

Posted
Posted

Does it have no cat at all...... hmmmm I have heard that no cat = HUGE fines :( when a cop looks under your car and see's no cat then there is a much high probability that you will get reamed. Best thing to do is to get a cat and gut it and whack that in, then at least it looks like there is a cat there to the cops.

Which can be easily changed for a proper cat + stock zaust to clear defects.

Side pipes are illeagal as they have no cat, and are freakin loud.

I'll take a pic of Revheads side pipe he uses for track purposes, it is louder than a 747!! Sounds awesome, but not worth the tens of thousands you might get in fines if pulled over.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • EndZee
      Fuel Pump Control Module & Dropping Resistor

      By EndZee · Posted

      Guys since i bought r33 gts25t coupe 1994 automatic a/t(manual swap 350z gearbox)  all i got is problems, always problems. Lets start with that when i turn key into ignition(ON) fuel pump doesnt always works. Sometimes i have to turn key twice Off/on/off/on until it primes. Its new, dw300 - 340lph. My gearbox broke so i did gearbox swap, install different intake manifold, injectors and i take pipes. Car was sitting in garage for more than half a year. I did assembly all not that long ago and when i turn ignition cant hear prime. All of sudden it stopped working. Theres many videos on YouTube how to make relay mod on r33 straight from battery so i did and it doesnt work! 😰 30 - battery positive  87 - positive from fuel pump to relay 85, 86 - one of two wires from original fuel pump wires(light blue, grey) and it didn’t work. so I check on ignition and took original BLUE relays wires from trunk, next to fuses. (I believe it’s IGN+ and ECU pin 18. it didn’t work…  tried connecting (IGN+ from og relay) and (ECU 104 from 1of4 FPCM wires) to my new relay 85/86 and it didn’t work.  I unplug FPCM. Didn’t work. im thinking what’s wrong   fuel pump is working, if I leave IGN+ on 85 and 86 straight to ground it works but it’s just nonstop. Since it getting constant 12v after key in ON. light blue wire gives me 6-8v.  so how this should be connected? What causing ECU not giving — on pin? Or I did sth wrong and that’s why it doesn’t work? I need negative signal on ECU that control fuel pump. What this should be?
    • Duncan
      M35 Brake caliper replacement

      By Duncan · Posted

      You can use your VIN to look up the factory part number somewhere like amayama, and then look to order new if necessary. https://www.amayama.com/en/genuine-catalogs/nissan Depending on price you might want to rebuild instead. @GTSBoy I had an interesting insight into US market parts when the Titan rear calipers were sticking. New calipers were dirt cheap, about 20% more than a rebuild kit....they are just considered throw away maintenance items
    • Duncan
      Most women will agree that parking is the most taxing part of driving

      By Duncan · Posted

      Funny, but really not funny. Thank god (most) f the world has moved on since then
    • Duncan
      Jacks that fit under GTR lips that can reach the subframe?

      By Duncan · Posted

      Lots of votes for driving onto a plank first; that is the quickest way I've found, 25mm is enough for my case but that will vary by car It also depends where you are going for. On the 32 I can get to the rear diff with my floor jack if I do that end first, and get it up on stands. Then I lift the front from either front tow hook as high as needed, also onto stands. Sometimes I need a small lift on the other tow hook to get it level enough If I do the front first I can't get to the rear diff because of the angle of the car Other options are getting to the front mount of the rear subframe from in front of the wheel (if only lifting one side, or just do both which is a bit of a pain compared to one lift from the diff), or also the gearbox cross member mount on the driver's side if you are  just trying to lift the driver's side. I This is the jack I use; it says 75mm clearance but of course that is only on the lower section so if you have to reach too far in like the diff you still get stuck. https://www.snapon-bluepoint.com.sg/category/Floor-Jacks/product/Floor-Jack,-2-Ton-Low-Profile
    • Duncan
      NC MX5

      By Duncan · Posted

      On the bright side, the weather will turn much nicer for working outside shortly....sounds like you might need to start on a neighbour's garden next
×
×
  • Create New...