Jump to content
SAU Community

And Remember Kids........

Ska

By Ska,
in Queensland

 Share

Recommended Posts

predator Grand Master

predator

Posted
Posted

THINK! Where does the enemy get his information -- information that can put you, and has put your comrades, adrift on an open sea: information that has lost battles and can lose more, unless you personally, vigilantly, perform your duty in SAFEGUARDING MILITARY INFORMATION?

THERE ARE TEN PROHIBITED SUBJECTS

1. Don't write military information of Army units -- their location, strength,, materiel, or equipment.

2. Don't write of military installations.

3. Don't write of transportation facilities.

4. Don't write of convoys, their routes, ports (including ports of embarkation and disembarkation), time en route, naval protection, or war incidents occurring en route.

5. Don't disclose movements of ships, naval or merchant, troops, or aircraft.

6. Don't mention plans and forecasts or orders for future operations, whether known or just your guess.

7. Don't write about the effect of enemy operations.

8. Don't tell of any casualty until released by proper authority (The Adjutant General) and then only by using the full name of the casualty.

9. Don't attempt to formulate or use a code system, cipher, or shorthand, or any other means to conceal the true meaning of your letter. Violations of this regulation will result in severe punishment.

10. Don't give your location in any way except as authorized by proper authority. Be sure nothing you write about discloses a more specific location than the one authorized.

TALK

SILENCE MEANS SECURITY -- If violation of protective measures is serious within written communications it is disastrous in conversations. Protect your conversation as you do your letters, and be even more careful. A harmful letter can be nullified by censorship; loose talk is direct delivery to the enemy.

If you come home during war your lips must remain sealed and your written hand must be guided by self-imposed censorship. This takes guts. Have you got them or do you want your buddies and your country to pay the price for your showing off. You've faced the battle front; its little enough to ask you to face this 'home front.'

CAPTURE

Most enemy intelligence comes from prisoners. If captured, you are required to give only three facts: YOUR NAME, YOUR GRADE, YOUR ARMY SERIAL NUMBER. Don't talk, don't try to fake stories and use every effort to destroy all papers. When you are going into an area where capture is possible, carry only essential papers and plan to destroy them prior to capture if possible. Do not carry personal letters on your person; they tell much about you, and the envelope has on it your unit and organization.

BE SENSIBLE; USE YOUR HEAD

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...