Jump to content
SAU Community

Recommended Posts

Hi there just wondering if anyone has a spare cefiro hand brake cable or hand brake for a 5 speed

Urgent..

Thanks

Hey mate,

good luck in finding one i did a auto to manny conversion on a cef a while back and couldnt find one anywhere so i just thought i'd let ya know that the r32 gtst coupe cable fits perfect if you have it lengthened by an inch well hope ya work something out

Ben

Hi

I have been working through this myself.

Gave up chasing original ceffy one. R32gtst handbrake fits.

Where the cable goes through the floor, the floor is already marked out, but you will have to drill and hacksaw it out.

The mounting bracket for the ceffy release is no good for the handbrake so you will have to make some spacers up to fit, fairly easy (have heard that others actually took the braket off R32).

There are short cables from the back of the handbrake that meet up with the cables going to the back wheels. You will need the short cables off the R32 and you will need to modify the ends to put a thread on with the right length (not too hard, need to find someone that can do that for you).

As for the console, I could not find one in Australia (that anyone would sell to me anyway) so after 12 months have bought one through Japanese Yahoo (see Mr Zac under sponsors)! They were quickly snapped up though! Just checked, none on there at the moment.

Hope this helps

Regards

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...