Jump to content
SAU Community

Recommended Posts

Ok before anyone asks, no I haven't banged my engine! (touch wood!) I have just been following the arias piston thread and thought that these seem to get the nod on some occations...

so I gather they are made in the USA, what are the prices here like?

87mm seems the go also what about 9 : 1 or 8.5 : 1 ?

I have found some in the states for $970 aussie... complete with rings etc....

ideas :P

Contact Markr34gtr is the man to talk to for CP pistons (very nice product) i used a set from mark on a r34 gtr vspec making 500rwhp plus happily. They run a 0.0035 clearance which is pretty good for forged pistons.

pete

Williams, that's pretty cheap if they are complete with rings.

One thing you need to be careful of with CP pistons, is that you get different rings depending on where you buy the pistons from. CP don't make their own rings.

I know if you order from CP direct, you get a japanese made ring. If you buy a set here, I'm pretty sure you get a US made hastings ring.

Also, the 87mm pistons you buy here are not an off the shelf CP piston, they are a custom piston and use a different ring width to the 86.5mm pistons (and the US 87mm pistons)

By the way Tomei pistons run 0.002" to 0.00225" clearance.

ok the reason I ask is I have found a place in the USA that does RB26 CP pistons... 86.5 and 87mm same as what cousin blitz has got....

I found the price to be rather reasonable, and that is with American rings matched to the pistons....

oh and that price would be me picking them up in LA :huh: but that isnt an issue....

but I am (touch wood a lot!!) not looking at doing this for a while, just curious as to the price diff locally...

ok the second part of my question has been skipped, comp ratio??

pluses and minuses for 8.5 or 9

cheers!

ok the reason I ask is I have found a place in the USA that does RB26 CP pistons... 86.5 and 87mm same as what cousin blitz has got....

I found the price to be rather reasonable, and that is with American rings matched to the pistons....

oh and that price would be me picking them up in LA :( but that isnt an issue....

but I am (touch wood a lot!!) not looking at doing this for a while, just curious as to the price diff locally...

ok the second part of my question has been skipped, comp ratio??

pluses and minuses for 8.5 or 9

cheers!

Hey Ben, I think you'll find the American 87mm pistons will be a different piston to Nicks ones. The Aussie distributor custom orders the 87mm pistons with thinner rings.

Hey Ben, I think you'll find the American 87mm pistons will be a different piston to Nicks ones. The Aussie distributor custom orders the 87mm pistons with thinner rings.

G'day Mik,

I can't say either way regarding the thinner rings, just that the CP pistons are for the RB26 and come in the 4 different options of size and comp....

I have emailed them regarding the rings spec...

Rob82...

no my engine is still in 1 piece... I was just asking out of curiosity....

I should think my engine should be going for sometime yet!!!!

here is the link to the site....

http://www.bnecustoms.com/store/home.php?cat=453

and CP

http://www.cppistons.com/sCompactNEW.htm

ben,

why aren't u speaking to jim @ dart? he recommends arias because of the ring quality (eqiuvalent of nismo rings)

at the end of the day its like asking the question of holden & ford?

it is personal opinion & they both have 4 wheels...

marko

hey mate :(

yeah I had the discussion about either of them a while back, I was just curious about the CP as I don't know much about them, and I know the arias are a good thing....

so how many km to go till u get some real boost? :)

hey mate ;)

yeah I had the discussion about either of them a while back, I was just curious about the CP as I don't know much about them, and I know the arias are a good thing....

so how many km to go till u get some real boost? ;)

Ben,

CRD recommends 1500km whereas Dart recommends 1000km

i may do 1250km :)

I hear you may be moving to Adelaide for good!?

Marko

yep! leaving old Sydney town...

well never say never.... but Adelaide is home, and plenty of GT-R friendly roads over there...

I'll just commute for work ;)

you will need some semi's for that car of yours now surely!!!

Williams, that's pretty cheap if they are complete with rings.

One thing you need to be careful of with CP pistons, is that you get different rings depending on where you buy the pistons from. CP don't make their own rings.

I know if you order from CP direct, you get a japanese made ring. If you buy a set here, I'm pretty sure you get a US made hastings ring.

Also, the 87mm pistons you buy here are not an off the shelf CP piston, they are a custom piston and use a different ring width to the 86.5mm pistons (and the US 87mm pistons)

By the way Tomei pistons run 0.002" to 0.00225" clearance.

ok this back in from the piston supplier....

"The rings are produced by CP Pistons. They are made of tool steel. Tool steel

is harder and stronger than the chromoly ones that everyone else sells. Plus

the tool steel rings seat a lot faster than the chromoly ones.

You also get Chromoly 5100 series pins, and wire lock retainers."

so they are made my CP?

ok this back in from the piston supplier....

"The rings are produced by CP Pistons.  They are made of tool steel.  Tool steel

is harder and stronger than the chromoly ones that everyone else sells.  Plus

the tool steel rings seat a lot faster than the chromoly ones.

You also get Chromoly 5100 series pins, and wire lock retainers."

so they are made my CP?

That is very odd. I was told CP don't make rings. The guys at CP in the states told me that they supply a Jap made ring.

The aussie dist supplies either total seal or hastings (US made rings)

Another weird thing...I always thought chromoly (ie chrome molybdeum (spelling??)) WAS tool steel!! ;)

But in any case, if I were to use CP rings, I would get them custom made to accept OEM rings and OEM tru arc locks.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...