Jump to content
SAU Community

Recommended Posts

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Micko, It shouldn't be too bad if you know what your doing, but your lucky your car will be cold, mine will be boiling by the time I get it to you.

I'm going home, over at the folks, so I'll be off air for 30mins, don't miss me too much:p

See'ya:burnout:

Originally posted by Micko

you got a filter removal tool paul?

Micko,

Unless you have a very thin one or the 3 pronged one like I have , forget it.

Get pwptf to come past on the way thru and pick up the 3 prong one.

Ya got a 3/8 drive ratchet ??

And you are correct , it will piss oil over the front diff which will dribble for about 2 days.

Damn GTR's. Hehehe

Cheers

Ken

And you are correct Loz , it is friggin hot with tomorrow being hotter.

Will be in front of aircond and TV from 7.30 to 2pm tomorrow though.

Cheers

not getting the manifold done at this rate

ken

Originally posted by Micko

you doing the manifold today ken?

i wish i knew cos i would like to have seen how it comes apart for myself...spose it would be much harder with someone standing there asking 10000 questions:)

Nope , walked outside this morning into the garage, decided I didn't need a 8 hr sauna so went back in and clocked up brownie points.

You know , making salads , cooking and washing up for the bbq.

Us married men have got it hard compared to the singles out there.:bahaha:

Cheers

Ken

mmm had two hour nanna nap - bad dream included! Think it may be beach for my tommorrow - then again to get to beach have to drive 40mins in unaircon car on second thoughts may just stay home in heated pool n spa with cold drinks close by.

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...