Jump to content
SAU Community

Recommended Posts

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Originally posted by Adrian_perth

neo, thought i'd give ya an idea as to what i am getting for my new exhaust :- hks hiper/blitz nur spec catback system

                     :- 3 Inch Highflow cat

When you gettin that Adrian. Will be good to see some at the cruz. I swear people must think that i steal skylines. I look under then all everywhere. freak!

Originally posted by Neo

When you gettin that Adrian. Will be good to see some at the cruz. I swear people must think that i steal skylines. I look under then all everywhere. freak!

i do it all the time. or pull a hard u turn while im driving to go and check a good looking import out :P

i love the funny looks u get :D

Psiker

i don't have it yet neo, but if all goes well i have my plans set out and mods should start hopefully next week if all goes to plan :D

at the moment i only got blitz filter, apexi front pipe and trust catback getting rid of front pipe and catback for new shit though :P

adrian :D

Originally posted by Adrian_perth

im turning 18 in august :D it's hopefully gonna go hard! i seriously wanna change it to manual but then again i'd get a better time with the slush box :P and maybe if i get that new turbo it will go even harder :D

adrian :P

wow RESPEKT!:uh-huh:

when i was 17 i had a 1991 TR magna, Auto, 2.6l 4 cyl

did u get the loan and all urself or buy outright with savings?

Psiker

Originally posted by Adrian_perth

i don't have it yet neo, but if all goes well i have my plans set out and mods should start hopefully next week if all goes to plan :D

at the moment i only got blitz filter, apexi front pipe and trust catback getting rid of front pipe and catback for new shit though :P

adrian :D

i thought apexi front pipe was good though? or u just want it to be the same the whole way thru?

Psiker

the catback is shit i cut on resonator and middle muffler sounds alright but i done like the welding and shit looks dodgy the muffle is tiny inside as well

apexi frontpipe is meant to be good, but it's only 70mm i dun think that is 3inch :P

adrian :D

Originally posted by Adrian_perth

my parents GOT the loan for me, BUT i am paying for everything, i was too young to tak out a loan so just got them to do it, no way would my parents pay for it :D

adrian :P

wow nice parents. my parents will go gaurenteer me (speling) but they wouldnt take a whole loan for me. specially with the houses and cars and the boat (now gone :D )

Psiker

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...