Jump to content
SAU Community

Whoretown WA

skyzerr33

By skyzerr33,
in Western Australia

 Share

Recommended Posts

gtrken Grand Master

gtrken

Posted
Posted
Originally posted by Nizmo

haha havent u had enough of me for one weekend paul? :D U saw it today its filthy if i dont do it then it'll be ugly and weird smelling (although i have either got used to it or its disappeared) for another week.

Quick question: My steering wheel vibrates at 80km and by 120km its shaking hella bad - its had a wheel alignment done but its still like this and its really annoying! Anyone know whats causing it?

Wheel Balance or your nuts are loose.

Cheers

Ken

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Popular Days

Top Posters In This Topic

Popular Days

Mr. Oizo Grand Master

Mr. Oizo

Posted
Posted
Originally posted by Nizmo

as in steering wheel loose? how do i tighten it - cos i wouldnt be surprised if that is the case :D

wheel.. as in allow wheels..

not ur steering wheel..

watch out..

coz it could fall off.. and do a lot of damage

gtrken Grand Master

gtrken

Posted
Posted
Originally posted by tenzero

Thanks Ken will do. I prolly would have used the RAC if you hadn't said that...so good timing.

Cheers.

D.

The RAC will spend more time doing the

* rip in seat , mark on rear squab , dirty hoodlining type report which any schmuck can see by using there eyes.

The important , check front end play , compression or leakage test, check syncros and oil cond test are bypassed cos they are baffled by the lack of V and too many camshafts.

Cheers

Ken

tenzero Contributor

tenzero

Posted
Posted
Originally posted by gtrken

The RAC will spend more time doing the  

* rip in seat , mark on rear squab , dirty hoodlining type report which any schmuck can see by using there eyes.

The important , check front end play , compression or leakage test, check syncros and oil cond test are bypassed cos they are baffled by the lack of V and too many camshafts.

Cheers

Ken

Nice, will keep all that in mind when I need to get one checked out.

Cheers.

D.

gtrken Grand Master

gtrken

Posted
Posted
Originally posted by Nizmo

Wheel balance done last week - alignment done this week and the guys that do it are pretty good at what they do - so i ruled that out!

Well then they must have got it wrong then.

Have you hit any kerbs or suddenly heard a loud bang not long after the wheels were balanced ?

cheers

ken

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Latest Posts

    • V36
      What accelerator cable can be used with greddy plenum

      By V36 · Posted

      HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • MBS206
      Chris' Toyota Mark ii JZX110

      By MBS206 · Posted

      I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...