Jump to content
SAU Community

Recommended Posts

Nissan Skyline R33 Driver Side Rear View Electric Mirror

$130

Fully Working, no damage, just needs to be re sprayed. (has scratches in the paint) Glass is perfect.

Had a little problem with malicious damage, and insurance was going to take a while to replace the parts (plus getting it all the way from Japan) so I got this one second hand to put on the car until then.

(original mirror was completely destroyed, so I needed something!)

anyway, these are $850 not painted from Nissan, so consider that when purchasing this one.

mirror.jpg

And I am not going to rip you off, I'm a genuine skyline owner with heaps of posts here.

Edited by The Mafia

lol are you serious?

Its a driver side mirror. Thats where it was installed on my car, and it looked correct to me... It wasn't like up side down or anything ...

anyway... ITs a drivers side.

Anyone need one? It works 100%, and with some paint, will be like new.

Anyway, unless you have reversed all the images or at least that photo of the mirror, i beleive my next picture will explain why i say its a passenger mirror

Using your car, and the photo of the mirror you took, i compiled the below diagram

mirror0nq.jpg

ok, I am gonig to be straight forward.

I had it on my DRIVER SIDE. I will take pictures tonight just to shut you up.

That picture is what I got when I was buying the mirror, so maybe they sent me the wrong mirror picture.

I can see your point.

I will make my point clear though,

THE MIRROR I HAVE IS FOR THE DRIVERS SIDE.

Edited by The Mafia

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...