Jump to content
SAU Community

Good Photo Locations

ECR033

By ECR033,
in New South Wales

 Share

Recommended Posts

ecl Mentor

ecl

Posted
Posted
the rocks.. all cars under the big bridge all in a staggered formation (you'll be blocking traffic but it doesnt get too busy late at night)

rocks.jpg

im not sure if this was taken at the rocks or whos cars they are but it looks like the rocks, it would be an awesome shot with 20+ cars.

hey, thats my car

thats a tunnel in homebush behind the tennis court

Goon Experienced

Goon

Posted
Posted

these suggestions were from another car forum: brackets is my opinion

olympic park (done to death)

blues point (as above, cliched)

general holmes drive (good location)

powerstation (the best, if your going for the industrial look)

milsons point (same as Milsons)

gladesville bridge (seculded, nice shots, but a bit boring, as there is no variety)

rhodes carpark (don't know that one)

Kel Veteran

Kel

Posted
Posted

For a different water/bridge backdrop, you could try The Esplanade, near Russel Park, at the back of Drummoyne.

There's parking along the edge of the water.

You might need to get there early to avoid lots of walkers/dogs/kids in your shots.

If you're really keen, you're almost always guaranteed a spectacular sunrise from this spot.

Kel

http://www.whereis.com/whereis/mapping/pan...1&direction=180

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Shizu
      Sheraaz's R34GTT Build

      By Shizu · Posted

      Omg Brake pedal removal.. FML!!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I mean, I can confirm the TPS is at 100%.... I can confirm when we installed the TB and setup the cable that the TB was indeed fully open at max pedal travel.. the same 'curve' (WRT MAP vs MAP) existed with the previous setup/TB/manifold as well... No, we did not do a run with no intake connected. I would love to go back in time to do such a run to rule out the intake. It would have also been good to do a run with the airbox lid off. There's a test there where increased IAT vs more available air could be a positive tradeoff. I remember taking the lid off my R34 Turbo setup back in the day and noticing a monster increase, even if IAT's did go up. Could be similar. Hard to test unless I find a very deserted road. 
    • LaurelPWR
      Forced Performance Hta Turbos

      By LaurelPWR · Posted

      That's actually encouraging to be honest. my motor was rebuild many years ago but it's probably done less than 30,000kms and fucc all limiter or drift, majority street / drag / roll racing. It'll be fine 💪🏼 I don't even have lines or a can for the cam breathers installed yet, there is zero oil residue or splatter on or around them, it drives beautifully so it seems healthy. Just a ticky lifter, yet they're almost brand new oem genuine Nissan and haven't done many kms at all...
    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      Have you confirmed the throttle body goes to WOT (and stays there) during the run?
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      I'm having a problem. I think it was mentioned above somewhere but can't see it.  I'm stuck in the cycle of, sand, filler, low spot again, put filler, sand, low spot again, now i put filler again and a thicker portion which seems to have helped but I got low spots in other areas. In the image. Circled in red thats where the original low spot was and the shape is the same as the red out line. I've more or less fixed that (still low spot up the top but now I have low spots where the green circled part is.  Is likely the issue that I didn't start with a course sand paper? I sanded the filler with 240 to reduce the risk of not going to far but maybe the issue is that I'm only taking off enough material to remove some of the filler but not the high spots. I now started sanding with 120 and I think I'm seeing a difference. I did fix one dent the other 2 are f**ked and seems like I made another low spot which is indicated by the furthest green circle on the left handside. Any thoughts and solutions?   Also second image. All of these rock chips, can they be filled in with primer or do i need to fill them all with filler/putty? So many rock chips on mine lol.
×
×
  • Create New...