Jump to content
SAU Community

Recommended Posts

Cubes,

If what you say is correct i will need to look into this quickly.

Just one question though, as you mention i didnt know that the normal trigger for the pump could shut down if the car stalled or such. Good to know really.

  • 5 weeks later...

Hi Guys,

This has been a really interesting read! I was hoping that you guys could clear up a few grey areas that i still have tho.

I am going to be running a bosch 040 or 044 pump inside my tank on my 32 GTR soon as i am upgrading the turbos and what not. My power aim will be around 320awkw and im wondering if this mod is required (as i know the pumps run approx. 230l/hr and 330l/hr respectively at 13.8v)?

Where abouts is the factory voltage control module located in the car?? Is it possible to rewire the pump but still use the factory voltage control module, as to only supply the pump with a lower voltage at idle but still have the 13.8v at higher rpm?? If not, im guessing the Jaycar kit that Sydneykid was talking about will be needed.

Thanks in advance for clearing it up for me.

Tony

I'm not sure about the other PFC's but when I dropped the PFC in to my R32 it constantly supplied the pump with high voltage. No more low voltage on idle with the PFC, In mine and other R32 GTST's I've seen.

I believe it would be possible to rewire the pump to still use the factory voltage control module. From memory I remember seeing something in the manual about the resistor pack to drop the fuel pumps voltage is located in the engine bay.

If its needed in your case.... suck and see... Unless you want to do it just to be safe and possibly save you having to go back for another tune, but chances are with a decent 044 even at the lowever voltage it will be fine. But really.. I don't know as there's a few variables that man influence if its up to the task, fuel pressure, boost and injectors size. Run less fuel pressure and the fuel pump will flow more.

anyone know what kind of current is drawn from the std fuel pump, same with the bosche 044 pumps?

with both of these running from direct power via a switched relay (each) finding its drawing alot of current making the car take longer to start

as in if i prime the system and turn the pumps off, then the car starts easier, then i switch the pumps on.

this is ona 550CA 60amp hour battery

  • 3 weeks later...

sorry about the late reply,

I would look at doing the oposite in your case and run larger cables to the starter motor. One thing that could be an issue is if your cables can not carry the current to run the starter motor, then the cable get hot during your start up, resistance of the cable goes up voltage goes down, then current goes up again! A very nasty circle.

Also a dircet cable from the negitive terminal to the engine block might help as well, if you dont have that already.

hmm its more ECU related than started motor ...

the dash lights go out when cranking then comeback on then the car starts

turning off the pumps just reduce the time the lights turn off for..

strange issue and i havent had time to play around with the currents that are being drawn when doing the above.

Strange,

does the starter motor sound like its struggling to turn the motor over. Do your self a favor if you have a multi meter connect it across the battery terminals and record what your minimum voltage was during the time your starter motor was turning over.

yeah will have a look, but no the starter turns the car over fine, just a momentary drop of power to the PFC

this is reduced further when jump starting the car..

can even get that bad if the battery is low that the car turns over but the lights never come on and it wont start ..

one day i'll find it

Have you had the motor out and rebuilt at any time?

May just be a bad earth.

motor hasn't been out, only ever head off..

have been looking into making my own earth kit for it all.... just a matter of free time which i dont have much of :D

only earth i know to be missing is the one the the turbo manifold.. which has been gone for years

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Kittens in first to claim dominance of the residence, then puppies later From past experience, the other way around can be problematic to say the least  Those weird "Dobby looking"  little kittens are not cheap....LOL
    • At least yours have parkour down pat. One of mine will still trip over his own shadow and fall over... He's a special type of cat... Ha ha ha
    • The question then becomes - was there any fluid coming from that hole before you did the rebuild ?    You may not have noticed, of course.   Depending on how you did the rebuild, the possibility has to be considered that somehow (cleaning ?)  fluid entered that hole and is now being 'forced'  out by small movements of the proportioning valve.   From the factory, there's actually a small rubber plug in that hole but with age and under-bonnet heat it's quite common for it to 'go missing'.  That rubber plug is designed to allow the venting process but also to prevent 'stuff' getting to the area (prevent corrosion, etc).   The plug is also not available as a spare part AFAIA. Personally I wouldn't race and buy a new master just yet but keep an eye on the area to see if the 'leak' continues.   If you're concerned about brake fluid damaging nearby paintwork, cable tie a piece of suitable absorbant material over the hole and remove/monitor occasionally.    Operation of the proportioning valve and the brake master itself won't be affected, but also keep an eye on brake fluid level, of course. In terms of a new master, the genuine part is getting expensive, unfortunately.  Amayama is showing AUD900+.   I was searching recently and there's an aftermarket part available from Japan made by 'Parts Assist': https://zenmarket.jp/en/yahoo.aspx?q=BNR32%2bBM50&p=1 Whether it's any good I have no idea, although in my experience Japanese aftermarket stuff is pretty good quality-wise.   The above site allows overseas buyers to purchase stuff more easily from Japan but there are fees and shipping costs, of course.   The original Japanese seller page is here: https://auctions.yahoo.co.jp/jp/auction/p1197401228 Copper/Nickel is fine but I still prefer bundy tube and it's also cheaper.
    • Your chihuahuas look weird!
×
×
  • Create New...