Jump to content
SAU Community

Recommended Posts

For Sale. R33GTSt Series 1 Headlights. Have bought 4 door lights and have no further use for these.

Good condition, nice and clear. As good as they get for Series 1.

Price $150 each or both for $250 ono.

Would prefer pickup or COD. Will be at NSW WSID drag day 5 Nov 2005. Items will be available to show then, or other as required.

Also Turbosmart bleed valve $40 ono.

Let me know.

El Bee

Link to comment
https://www.sau.com.au/forums/topic/92947-fs-r33-s1-headlights-bleed-valve/
Share on other sites

Can you PM me your number buddy.  Interested in the headlights.

PM on its way.

Would prefer local, but can organise something.

Will discuss.

El Bee

hey mate ive pm'ed u if u dont recieve it my number is 0405 189 388

im in sydney and ill pik up from ne where, ill b at the drags on wed night. im in urgent need for the valve as my project will b finished on wed.

hey mate ive pm'ed u if u dont recieve it my number is 0405 189 388

im in sydney and ill pik up from ne where, ill b at the drags on wed night. im in urgent need for the valve as my project will b finished on wed.

Reply sent

Here are pics of Headlights.

El Bee

OK. I am not the greatest photographer with the greatest camera but this gives an idea. Can be viewed drag day for the Sydneysiders.

post-1570-1130751655.jpg

post-1570-1130751691.jpg

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...