Jump to content
SAU Community

Recommended Posts

That ad should say KPGC10 for a real GTR the standard 2 door GT skyline is KGC10 and also the KPGC10 GTR was fitted with the 1998cc 160hp double over head cam 6cyl S20 engine! Not the L28!(280Z) and the KGC10 was Powered by the 1988cc 106hp OHC 6cyl. G7 series engine and later the 1973cc 109hp OHC 6cyl. L20 engine!

Still it is one nice car!!

Don't think I would pay that price though!

MEGA

I am no expert but I would imagine that your rather unique and enviable purchase :( has much much more in common with the 240K, as the 240K was the KGC10's immediate successor. Apparently the sedan version (not the twin cam s20 GTR) was exported to some wierd places like the Netherlands with the L24 engine -which made then unique as the car was never sold in Japan with more than 2 litres. As with the 240K, this generation of Skylines had IRS at the back if a 6 and rear leafs and a shorter body structure forward of the bonnet if a 4 cylinder.

I have a road test or two of the 240K and Wheels Magazine mentioned that the setup, whilst similar on paper to the 240Z was quite different, and superior in some ways too, such as tail squat under acceleration.

I know this is not much to go on, but I hope it helps.

Having a L28 in your car makes sense as the S20 motor, whilst looking and sounding more exotic, probably is less robust, costs heaps to repair and parts would be mega expensive and hard to get - especially in sunny Perth! Just make sure you drive it on sparsely trafficked roads - you don't want some retard hitting you (touch wood), what with panels not exactly being thick on the ground.

Sadly I would imagine there would be very little detailed technical info on these cars as they were not widely exported. Internet browser transaltion software will become a close friend, unless you read Japaneseor have a friend who does

If you can post a piccie or two - that would be great. :D

Hakosuka igreat handle there!) has it right; the CG10s are quite similar to CG110s under the skin. Suspension geometry was effectively the same between both and the cars are structurally similar across the forward section of the floorpan, toeboard, cowl and engine box.

The single biggest structural difference was that the two-doors rode on a shortened wheelbase vis-a-vis the sedans, cropped where the rear clip welds to the floorpan - the two-doors had a die insert which shortened the pan. This mean that with fours and sixes both offering two-door hardtops as well as four-door sedans and wagons, there were four different wheelbases for CG10s. When the CG110 'Ken & Mary' Skylines (240Ks in export) came along, a single wheelbase from the firewall back was used for all models, so the four/six meant that 110s had 'only' two wheelbases.

Sorry to babble so long, but Ai no Skyline/Hakosuka and Ken & Mary Skylines are really near and dear to me from my misspent High School and Uni days in Japan. But I still want to make an RS Turbo out of an R30 five-door...

bwob

Talk to Noel Sinclair - 0438 511 652

You can also get him, apparently, at [email protected]

Also, I'm told, our VP Wayne ([email protected]) has one also, and is willing to offer any advice.

Thanks for all your help guys.

MegaGTS4 - I listed it as KGC10 GT-R "Specification" Coupe, thats how they get referred to domestically when they have the GT-R bodywork and spoilers, if you'd ever seen a totally stock KGC10 you'd see what I mean. Plus no-one in their right mind would actually use an S20 these days - a super hot 2.2L will only put out 260 horse and they are brittle as hell. If I wasnt aiming to historic rally the car then I'd put a twin cam RB30 NA in it with throttle bodies.

Jash

MegaGTS4, as far as I am aware the KGC10 Skylines (in other words the new shape from 1968 and the first Skyline to be badged as a Nissan from the start) was never fittedwith the G7 (Prince design) engine that was fitted to the previous shape Prince/Nissan Skyline GTB. I could be wrong but I thought that any 6 cylinder Skylines - with "P" for Prince in the model code to - from this model onward had the L20 series etc.

A 2 litre SOHC GT or GTX (twin carbs - like the Jap spec 240Z motor) model hardtop or sedan made to look like a GTR can still command very good money in Japan if they are done right. If anyone say the last Performance Imports Skyline special edition magazine they would know what I mean.

bwob, how foolish of me to have forgotten to mention the differences in wheelbase between the hardtop and the sedan for the pre 240K era Skyline! I believe that the 240K type GTR had rear disc brakes too.

Does anyone know how many of these KGC10 Skylines (especially the tasty GTR) ever made it to Australia. They must be even rarer than stuff like the Toyota 1600GT - an official import by the way - less than 10 in Australia of them.

the KGC10 Skyline... was never fittedwith the G7 (Prince design) engine that was fitted to the previous shape Prince/Nissan Skyline GTB

That's right. The G series six was dropped from the Skyline when the S54A and B were discontinued shortly before the introduction of the CG10. From the launch of the CG10 the Nissan-designed L series six was standardised in all Skylines (it had already replaced the G7 in the Gloria when the 'Royal Line' Glorias were released in 1967).

Nissan kept the four-cylinder G series engines around in short nose Skylines till the mid-life facelift for the CG110 was announced. Introduction of new emissions laws in Japan was the public rationale for the move to L series fours in place of the Prince-designed engines.

bwob

GTAAH-Sorry if I misread your ad!! (The car is probbably worth every cent!, but I personally wouldn't spend that much money on a car that can't be registered, personal choice more than anything!)

HAKOSUKA & BWOB- I was just quoting something I read on the net about the GC10 series sorry I must be wrong then.

And these sites must be wrong too!!!

http://www.skylinesdownunder.co.nz/history...ry/history.html

http://www.geocities.com/toasterino/Skylin.../SkylineGTR.htm

http://www.frinkiac7.clublotus.com/CarReso...SAN_SKYLINE.htm

MEGA

P.s BWOB its GC10 not CG10 get it right!!!(I had too)

Mega,

They are very much able to be registered - anywhere in Australia without a compliance plate. Anything 15 years old falls into that category. The 15 year old situation isnt changing with the new regs. We can even drive LHD stuff over here without converting when they are 15 years old.

Jash

Mega, the references I was using - with one exception mentioned below - were my collection of Japanese brochures (which are pretty complete from the ALSID-2kai of February, 1960 up to and including the R30 introduction) and a special one-shot commemorating the 400th issue of the Japanese monthly Motor Fan (published by San'Ei Shobo, October, 1978) which has proven to be a real gold mine for data from every Japanese manufacturer - even weirdies like Flying Feather, Mikasa, Ohta and Tama Jidosha - from 1917 through early 1978.

All the information I have supports the fact that the S54-1 Prince Skyline GT-A (the first Skyline to use the G7 in-line six and announced on 13 March, 1964 ) kept the G7 up to the launch of the L20 powered CG10 Skyline 2000 GT which went on sale on 9 October, 1968.

The Motor Fan special also says that about 50 S54A GT-As were shipped to Holland in January, 1965 with the Prince G11 six (2497cc and 130hp), the only S54s built without the G7. I'd love to have one of those mutants in the garage.

I did stuff up about the G7 in the Gloria, however, by relying upon memory rather than checking the facts. When the Royal Line Gloria was launched on 15 April, 1967, it indeed retained the G7 and kept it till a mildly facelifted version appeared on 20 October, 1969 with L20s replacing G7s under the bonnet. Sorry about that.

bwob

There ya go Mega, you cant always believe what you read on the net and you cant beat oldschool when it comes down to it. I had the option to buy a restorer spec 54 about 2 years ago and didnt - I'm still kicking my own arse for that. Bwob didnt Oz score some proper GT-B spec 54s?

Jash

Bwob didn't Oz score some proper GT-B spec 54s?

Apparently a handful were brought into NSW by the old Prince importer. I e-mailed Robbo (Peter Robinson) and chatted with Mike McCarthy on this for a possible piece in the 50th anniversary issue of Wheels and both recall seeing a couple in the mid-1960s at the importer's office.

I was reading (in the Motor Fan special) that the Skyline development team at Ogikubo built two S54s with GR8 four-valve twincam sixes - predecessor to the S20 - from Prince R380s for evaluation. They were sort of the philosophical prototypes to the CG10 GT-R. I think I'd rather have one of those than a Dutch 2.5 litre S54.

bwob

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did this end up working? Did you take some pictures?
    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...