Jump to content
SAU Community

What would you do?  

7 members have voted

You do not have permission to vote in this poll, or see the poll results. Please sign in or register to vote in this poll.

Recommended Posts

Well, i've lunched the turbo on my RB20 on the way to work today...

It was the compressor blades that broke (not exhaust like normal) and there is fine metallic dust through the intake, and it appears to be on the tops of the pistons as well... Now, i found larger chunks of metal through the intake, i just don't know if any of those made it into the engine....

Now, the choices i have are:

Put another turbo on and hope for the best

Buy a wreckers engine and hope for the best

Get my current engine rebuilt

Now, there are pros and cons of each.....

Pros for putting another turbo on....

Cheapest option

Cons for putting another turbo on....

Could spend money/time putting it on only to find the engine is fubar, and be in exactly the same situation

Pros for buying a wreckers engine....

'relatively' cheap option

Cons for buying a wreckers engine....

don't know past history, it could have been thrashed, on the verge of death etc... could only last a month or 2 before it dies and then i'm back in exactly the same situation

Pros for rebuilding the engine....

Will be a brand new engine, you know exactly whats done to it, how its been treated, should last for years and years to come (i'm looking to keep the car for a fair while hopefully, as it owes me too much money to sell), the engine has 190000km on it anyway, so its just about due for a rebuild...

Cons for rebuilding the engine....

Is the most expensive option

What would you do in this situation?

Keep in mind that i need the car for work, but i could probably get away without it for a week or 2....

Link to comment
https://www.sau.com.au/forums/topic/95779-where-do-i-go-from-here/
Share on other sites

I very much doubt that your engine has sustained damage. Reason I say that is that any metal pieces would have to make their way through the intercooler before ending up in the engine. This alone would probably ensure that only the finest particles would end up in the engine. It is possible that the engine is damaged, but as you are going to have to replace the turbo anyway then I would do that first and then see what happens from there.

i would take all the piping out and the intercooler and even the inlet manifold and clean it all as much as you can that way if there is nothing in the intake to destroy your engine if its not allready destroyed if you put a new turbo on then your home free.

Last thing you want is having to put the turbo back on and it run great for 2 weeks then the engine spits it.... take the time and work out where your at first before inspecting the bank account for a rebuild.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, it went to Unigroup for a run in and tune on Friday, everything went (generally) well. In terms of fixes, the engine was good and there were no leaks. It needed plugs (I hadn't checked them because the coil pack cover was on a new engine and I couldn't imagine they weren't new.....but turns out the temporary plugs to just keep it sealed up were in there.....new plugs gapped to 0.8 and it was fine from there. Also, there was a little preload on the clutch slave which caused some slip. I haven't had the box off so I don't know what the clutch looks like; my guess it is brand new and the pedal had not been adjusted....backed that off a bit and it held fine. Last thing will have Dose crying....the idle especially when cold is a bit difficult between the cams, forward plenum, atmo blow off valve and an 80s air management system. It is fine when hot but a little uneven when cold, will see if I can sort or at least improve that one cold morning. Other than that, tuning went fine. It made 245 but was pulled back to 227 which 2 opportunities to improve in future. 1. The factory CAS is not great and was jumping around at high RPM, so Mark took 2 degrees out up top (that is why it stops making power and lost 20kw). Very safe this way and the extra power is available but will require a more modern ECU and better cam (or even better crank) sensor 2. The 2871 in factory housings is very big for a low mount, and the internal wastegate is too small, so it was creeping from mid range all the way to redline....the duty cycle on the boost controller is turned down a little for safety. That is much harder to fix, it would need a large external gate and that would require a whole bunch of other changes, so it will go as it is for now. It feels nice and healthy and safe, so should be good for about a billion laps like this.
    • what sort of caliper are they? If they are a slider and you gave everything a good clean, you might need to regrease the pins. My guess though is they will come good after some abuse as suggested above
    • I don't know what you should expect with an LS, but the oil pressure sounds terrible, sorry. As for the brakes, you can get fade from the pads not just the fluid, although generally that feels like a wooden block not doing anything while fluid feels like an oh shit there is no pedal so you can generally tell. What pads are you running front and rear?
    • Went over my datalogs on a whim and noticed a worrying combination of events. High RPM High Temperature Low Oil Pressure Knock Retard I bought some 10w-60 because I actually think this will be better going forward given track temp is 125C and 10-40 will actually be thinner in those environments. I know I had a leak but it's not entirely sure how much pressure loss can be attributed to that. The knock retard does correlate with all of the above. When it's not present oil pressure is higher. And by 'low' I mean at 6800 RPM the oil pressure was recorded as low as ~35psi pretty constantly. Which is obviously very not good. I'm hoping that thicker oil that ISNT LEAKING will result in a bit more pressure when I need it. Also in the last session I got a very spongy break pedal. I bled the lines as the car is on jack stand right now with the wheels off and I noticed... no air in the lines? Maybe the tiniest bit of tiny frothy bubbles for the first 0.1 seconds of bleeding the whole car? The breaks did come back to me after I backed off (and felt fine driving normally). Doesn't appear to be any leaks anywhere that I can see. Any thoughts on that?
    • Solution, run shitter tyres. Let wheel spin be your weak link 😛
×
×
  • Create New...