Jump to content
SAU Community

Raizin Volt Stablizer

d00dz

By d00dz,
in General Maintenance

 Share

Recommended Posts

d00dz Grand Master

d00dz

Posted
Posted

Hi all..

Went to justjap and bought some random things one of them being the volt stabilizer...

Just wondering how and where do people install this?

Running a long earth wire from the battery to the distributor? or?

Any pictures and/or advice would be greatfull.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/96540-raizin-volt-stablizer/
Share on other sites
  • 9 months later...
anexiole Community Regular

anexiole

Posted
Posted
Hi all..

Went to justjap and bought some random things one of them being the volt stabilizer...

Just wondering how and where do people install this?

Running a long earth wire from the battery to the distributor? or?

Any pictures and/or advice would be greatfull.

Cheers

'err isn't the thing to be installed next to the batt on the boot of a skyline?

JaseR33 Collaborator

JaseR33

Posted
Posted

I ran 4gauge power cable from my neg terminal in the boot to the bonnet then wired up all earths from there. The stabiliser box is mounted next to my batt in the boot. will get some pics when i get a chance:)

anexiole Community Regular

anexiole

Posted
Posted

thanks, man. it would clear lotsa things up..

to run the 4 gaugecable to the engine bonnet, u would have to take off ur rear seats and run the wire all the way to the front,yea?

I ran 4gauge power cable from my neg terminal in the boot to the bonnet then wired up all earths from there. The stabiliser box is mounted next to my batt in the boot. will get some pics when i get a chance:)
JaseR33 Collaborator

JaseR33

Posted
Posted

I had to remove rear seats to run 4 gauge cable. I ran it under the floor carpet on the drivers side with the stock wiring as there are guides in place. The 4G cable is thick and difficult to thread under the carpet without removing bolts for the drivers seat and seat belt anchor.

I then ran it uder the drivers kick panel and through the fire wall just above the throttle pedal which leads to the drivers side wheel arch under the guard. There are guides there that run behind the drivers side headlight in to the engine bay.

Took a total of 6m of cable to run it through properly.

From the 4G cable in the engine bay I mounted all the earthing points.

Afterwards I did notice better sound quality of my audio and brighter interior lights i think... :laugh:

Cheers

Cheers

anexiole Community Regular

anexiole

Posted
Posted

If anyone could come up with a TUTORIAL on how to do this (with pics too) , it would be good :O

thanks'

I had to remove rear seats to run 4 gauge cable. I ran it under the floor carpet on the drivers side with the stock wiring as there are guides in place. The 4G cable is thick and difficult to thread under the carpet without removing bolts for the drivers seat and seat belt anchor.

I then ran it uder the drivers kick panel and through the fire wall just above the throttle pedal which leads to the drivers side wheel arch under the guard. There are guides there that run behind the drivers side headlight in to the engine bay.

Took a total of 6m of cable to run it through properly.

From the 4G cable in the engine bay I mounted all the earthing points.

Afterwards I did notice better sound quality of my audio and brighter interior lights i think... :laugh:

Cheers

Cheers

Craved Grand Master

Craved

Posted
Posted

isnt there like 4 or 6 wires off the stabiliser? each of these to hook up to individual parts of the engine bay,

CAS, starter, earth strap to block, throttle body etc ??

i would run 1 wire from boot to engine bay, hook stabiliser to the wire in the engine bay then each bit to the spot on the engine...

but thats just me

hicas_posse Community Regular

hicas_posse

Posted
Posted

hmmmm... how do you run the wire from the boot to the engine bay?

i know how to bring it from the boot to the front seat(by taking the rear bak seat off but after that i'm as long as the guy is too.

isnt there like 4 or 6 wires off the stabiliser? each of these to hook up to individual parts of the engine bay,

CAS, starter, earth strap to block, throttle body etc ??

i would run 1 wire from boot to engine bay, hook stabiliser to the wire in the engine bay then each bit to the spot on the engine...

but thats just me

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • blind_elk
      Wheel refurb?

      By blind_elk · Posted

      The powder coating came in at $250 EACH. The TRX rims got a coat of clearcoat on the outside only.    
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Bit wet, but YUMMY
    • GTSBoy
      Pops when backing off throttle, rough-ish sound through rev range.

      By GTSBoy · Posted

      Keeping in mind that I am currently getting flat 10 L/100km on my RB25DET, which means >>500km/tank. I would test this car for vacuum leaks, check codes and AFM signal with NissDataScan as D says, check plugs, do a compression check while they are out.
    • Duncan
      Pops when backing off throttle, rough-ish sound through rev range.

      By Duncan · Posted

      It is hard to be specific half way across the world...but it *seems* like it might have a minor issue. Is the idle stable and does it rev smoothly? I would not expect any pops out of what I am assuming is a standard ECU, standard tune, standard exhaust. You can use Nissan Data Scan to find out exactly what is happening when it runs, the cable/software is reasonably affordable if you are not planning on changing the ECU (which hopefully you are not with an NA skyline) BTW your mileage may not be that far off, these are heavy old tech cars, and being NA might mean you use a heavy foot to keep up with traffic....
    • AdiR34
      Pops when backing off throttle, rough-ish sound through rev range.

      By AdiR34 · Posted

      Hey guys! Y'all are the masters so figured I'd check in on a few items here. - My engine sounds ever-so-slightly more raspy than the other NA RB25s I've listened to. It's barely noticeable but definitely a slightly different sound. - When I back off the throttle at high RPM, I will sometimes get a pop out of the exhaust, assuming this can be diagnosed as misfire. Some history on the car: - Had an exhaust leak in auction sheet but was claimed to be fixed by seller (bought from USA importer).  - Car's coil packs and sparks were replaced when it was sold to me, but unsure on what the gap is and whether the coil packs are correct.  - A prior mechanic had misdiagnosed a pilot or throwout bearing sound as LSPI/detonation. Had played with timing a bit, pops/raspy sound of engine just got worse. Got timing reset. - Had failed emissions a few times. First time went in as is, failed. Second time, replaced cat, still failed, running rich as hell. Third time replaced o2 sensor, passed. Car still smells gassy though. - Timing belt and valve cover gasket also replaced.  - Gas mileage is... low. about 350-400K per tank.  Any idea if I'm having any serious issues here or does this all sound like normal old NA RB stuff and I'm fine to drive it with the pops/slightly raspy engine? If it'll help, I can get drop a video of the sound of the engine.
×
×
  • Create New...