Jump to content
SAU Community

Recommended Posts

hey all just bought a 4 door 32 and i had coil packs tested, they were stuffed got new splitfire coil packs and irridium plugs and put them in and a new oxygen sensor also went in. and i still seem to have a rather bad misfire or hesitation while im driving the car on boost or not.it is running an auto mines ecu and car is manual and the plug on the cat convertor has been cut off in japan so the dash light flashes constantly can anyone help me please.

i have also checked afm

any help would be much appreiciated

MYP16

Link to comment
https://www.sau.com.au/forums/topic/97555-r32-hessitating-very-bad/
Share on other sites

also may sound stupid, check your oil level

where any vacuum hoses changed? i know i had problems when i used bigger hoses for my turbo's bleed valve and blow off set up, started causing a lil drama's

also take out those irridiums and get some ngk copper plugs, ull have less drama's

Edited by nemz
hey all just bought a 4 door 32 and i had coil packs tested, they were stuffed got new splitfire coil packs and irridium plugs and put them in and a new oxygen sensor also went in. and i still seem to have a rather bad misfire or hesitation while im driving the car on boost or not.it is running an auto mines ecu and car is manual and the plug on the cat convertor has been cut off in japan so the dash light flashes constantly can anyone help me please.

i have also checked afm

any help would be much appreiciated

  MYP16

My Suggestions;

1. What plug gap? Should be 0.8 mm, not 1.1 mm as they usually come.

2. Have you checked the ignition timing? Autos run more initial ignition advance than manuals, it may be necessary to set the timing at 20 degrees instead of 15 degrees. Try both and compare.

3. Have you had a leak down test done? Results?

4. I have never seen a Mines ECU work very well in Australia, get a hold of a standard ECU and compare. You could spend much time and money chasing other things when the ECU is the real problem.

5. Pull the bulb in the cat overheat warning light.

Hope that helps

:( cheers :)

un plug the 02 sensor. it sounds silly but it will eliminate it as a problem. evan if its new it could be the wrong one.

also if you can get hold of a fuel presure guage it would be handy.,tell the mechanic to test it while hes up it.

(be carful not to place it under the wipers as i broke a windscreen doing it that way)

does it have a foam type airfilter,or any aftermarket air filter?

from what it sounds like these are my main suspect parts:

1-air flow meter

2-fuel pump

3-02 sensor(will be ok when cold but f**k out after about 2-3 mins)

4-ignition igniter.-finned thing at the back of the motor

5-coolant temp sensor

if had to fix a whole heap of these problems with cars coming of the boat, and its usaly in that order.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
×
×
  • Create New...