Jump to content
SAU Community

Recommended Posts

hi people im selling my T51 turbo i never had the chance to blot up this monstar, i Brought this puppy about 1month ago it was goin to go on a Rb 25/30det. but my plans have changed to a rb26dett with twin hks 2830 pro s turbos. im Located in melbourne i will be able to post anywhere, it will cost $80 to post coz its 20kg's

i paid $2000 and selling for $1300frim*

Spec's

T51 Turbo rated at 800-1000hp

Checked by ATS turbo professionals, who said it was in very good condition.

No shaft movement (Bush type Turbo)

Oil cooled only

HKS Stamped on rear housing

Garret Tag on the Centre of the turbo

Garret Front cover

-Compress wheel is 7cm across A/R .72

Front compressor bell mouth 10cm across

-Exhaust Wheel is 7cm across A/R 0.90

T4 Flange

Serial number on turbo - WG 7011J

Comes with Dump/front pipe to suit

post-15174-1134207155.jpg

post-15174-1134207183.jpg

post-15174-1134207221.jpg

post-15174-1134207340.jpg

Edited by JETR-32
Link to comment
https://www.sau.com.au/forums/topic/98037-fs-hks-t51/
Share on other sites

  • 3 weeks later...

to bolt this turbo up to an rb20 it will need alittle work. frist u will need to buy a T3/T4 Adaptor plate from autobarn about $30 to blot the turbo up to the standard Manifold. then u will need to cut a hole in the Manifold and weld up a small pipe for the wastegate (all this can be done at anywork shop for no more than $100) for the dump/front pipe i have one and will give it 2u for free. blot up the oil lines and off u go. about a dayz work if u get help.

Hi.  Sorry to sound like an idiot, but how much work would I need to do to put this onto a rb20det with 3" intake/dump, and 500hp fuel pump?  Everything else is pretty stock.

Link to comment
https://www.sau.com.au/forums/topic/98037-fs-hks-t51/#findComment-1847547
Share on other sites

hi i enquired about this a while ago, the dump pipe/and front pipe bolt up to the cat on my gtr? or do i have to get a pipe made up.

Do you have access to a manifold to suit a rb26? and wastegate?

hi mate the front/dump pipe is for a high mount but can be modifly by any shop. for the manifold and wastegate talk to "RACESPEC" on this forum he can hook u up with a package. if u get a high mount manifold the dump/front pipe will bolt rite up

Link to comment
https://www.sau.com.au/forums/topic/98037-fs-hks-t51/#findComment-1851215
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • With ordering the belt, you're doing water pump and the idler and tensioner at the same time too yes?
    • This is just a dumb way of keeping the wastegate closed to make more boost. Undo it and either follow the factory setup or redo it properly. Manual boost controllers just use a spring preload to determine when to close in response to boost pressure so it no longer vents to atmosphere.
    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
×
×
  • Create New...