Jump to content
SAU Community

Pics of my old valve

red17

By red17,
in Western Australia

 Share

Recommended Posts

red17 Experienced

red17

Posted
Posted

Heres a couple of pics of the damage done to one of my valves a couple of months ago after a night out at the drags turned pear shaped.

I have my doubts about all of this damage being done on the night in question, in fact i think it was low in compression on cylinder 6 when it came off the boat in September. I just made it much worse when an electrode broke off a plug and went through the valve. :eek:

In all only 2 valves required replacing at a cost of 55 bucks each. Not too shabby. But it could have been MUCH worse.

This was when running 0.8 bar on a stock cooler on a relatively cool October night.

Red17

Link to comment
https://www.sau.com.au/forums/topic/9826-pics-of-my-old-valve/
Share on other sites
red17 Experienced

red17

Posted
  • Author
Posted

Mayhem,

Id only had the car 2 weeks before this happened, ran it a few times on 0.8 bar before i went down the strip without problems. My own stupid fault i suppose. But it goes better now than it ever did so I figure some of the damage on that valve was done before me.

Red17

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Ozdavroz
      WTAC 2025

      By Ozdavroz · Posted

      Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • bcozican
      WTAC 2025

      By bcozican · Posted

      i will be there 😁
    • patrickxdf12
      Squeaking clutch/throw out bearing

      By patrickxdf12 · Posted

      Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Murray_Calavera
      WTAC 2025

      By Murray_Calavera · Posted

      Yeah mate, never miss it.
×
×
  • Create New...