Jump to content
SAU Community

Recommended Posts

Hi guy's,

99gtt and others, if someone is in Sydney and can come in to see us with thier 4 door, we can see what changes we need to make and we can make up the 4 door kit.

FLIP, the front bar by itself is $440, as is the rear and skirts are $300 for the pair by themselves.

xr8eater, We will be looking at a R32.4 and R33.4 conversions next year. Once we have the normal wide body guards available for each model, then we can modify them for the conversions.

choyda, No he put the canards on himself.

Jeff.

Link to comment
https://www.sau.com.au/forums/topic/98299--/#findComment-1801734
Share on other sites

xr8eater, will do.

E-Lu-Shun, I will send you a PM.

R34, We haven't got any kit for them as yet. You must have one of the very few in the country at the moment. I have heard they will be released here new next year I believe, although they are apparently the shitty FWD and 4WD versions. We will be working on a Z33 kit sometime next year and we could probably adapt a kit for the V35 from there.

Jeff.

Any kits coming for V35?

Link to comment
https://www.sau.com.au/forums/topic/98299--/#findComment-1803509
Share on other sites

R34, We haven't got any kit for them as yet. You must have one of the very few in the country at the moment. I have heard they will be released here new next year I believe, although they are apparently the shitty FWD and 4WD versions. We will be working on a Z33 kit sometime next year and we could probably adapt a kit for the V35 from there.

Jeff.

OK thanks please keep me posted.

Yes my car arrived yesterday from Qld.

Don't think V35's come as FWD...maybe you are thinking Maxima?

Link to comment
https://www.sau.com.au/forums/topic/98299--/#findComment-1809779
Share on other sites

Unfortunatley by the sounds of things they will be coming out in a FWD format in Aus :P:D , or at least that is the word from my mate at Nissan.

Pretty crap hey.

Jeff.

OK thanks please keep me posted.

Yes my car arrived yesterday from Qld.

Don't think V35's come as FWD...maybe you are thinking Maxima?

Link to comment
https://www.sau.com.au/forums/topic/98299--/#findComment-1809806
Share on other sites



  • Latest Posts

    • Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
    • I just stack 2 pieces of 200x50 timber on top of each other. Total length about 900mm, with the top one being a little shorter and both having a 45° angle cut on them to make the front edge a bit of a ramp. Put these in front of each front wheel, drive up on them, throw the trolley jack under. Takes 1 minute. Scissor jacks can eat a bowl of dicks. I never use on under my car unless desperate.
    • Well, yeah. But I just expect everything other than my car to feel like a bucket of shit anyway. I still miss my Alfa 116 so much though. You could run over a 20c piece and tell whether it was heads or tails.
×
×
  • Create New...