rsx84

yeah basic stage 1 upgrade, good fmic, pod?, full 3" system remap for ecu and a good tuner!!

does your mr have that hard/soft control for the front?

with a good remapping and tune job you should be looking around the 160rwkw mark!!

when i got my konis they also had (camber tops)? that came with the shocks, don't know if they were an extra needed as the car had the electronic (hard/soft) tops before?? i have the orange konis like the ones on e-bay they are height and firmness (harder/softer)adjustable!

phat i was going to try exit mold, let it sit in there for a few hours them drain it and a wipe down but never got around to it! also i just look at the ebay konis 3days to go and i found them by just doing a skyline search second or thrid page? $142.50 is the current bid.there are also a set of the same taillights as the ones i sold you for $30 (they have a large crack/hole in them)

don't those r32 GTR rotors look just so inviting!!

i second that, have you looked in to the n/a rb25 head transfer as it adds rpm and a heap of torque across the rev range! my flatmate has been quoted around $1300 including labor to do the swap on his r31!

bingo! i should of used a few more discriptive words in the post!

Cheers...Matt

ghostrider: spoke to that place you posted the number for yesterday and with my hr30 i'd have to swap the whole rear end to use the dr30 rear disks and its $1500 for the diff alone r200 4:3 ratio?? any advise?

if you use the speedo cable from the gtr its not electronic and has been used by a few r31 boys with the same problem!!

now i'll go with the rb25, but something i hav'nt throught of is will it bolt up to the rb20 manifold??

as the name says i'm looking to repaint my car and need to know the name or even the code for the red NISMO uses on its race cars!

try www.rb20det.com

what about using the calipers from the r33 as well as the r33 bracket should bolt up to the r31 strut??

just thinking with your rb30/25 conversion will the brake set up your engineering it with be enough as thats a big power to weight ratio?

bargain and then some, i'm paying $990 for 15x7,15x7.5 but they are sick and fill the guards like a glove, with the 3 peice bolts they look so much better than the cast sets you can get. fitted the strut brace today, i've got around 2mm of play before the inlet manifold hits the brace so might look into a stabalizer shock for the engine? whats the gap you have with your cusco??

can someone help with tacho info, i know the signal running from the r32 ecu runs through a greenie blue wire, the problem is the r30 tacho has three wires, yellow blue and black, can some one let me know which r30 wire takes the signal? i'm thinking the black is earth yellow power blue signal???

yeah mate i had a good look this morning i unhooked the wire from the sensor and tryed to start her no go would just kick over not fire up!!, work on this info. the r32 wire thats connected to the sensor is blue, thats been cut at the sensor, a new plug was put on then run to the conection at the wiper motor and is spliced into a yellow with a black strip wire (there are 9 wires running into this plug and 2 are yellow) i'll confirm the colour tommorrow!

i have this problem with my r31 every once and a while, theres a temp sensor linked to the injectors that plays up, it will shut the injectors off, no fuel flow at all, with my wiring there is a wire running from, ok you know where the radiator connects to the head at the top there are two sensors, now the one closest to the head has a wire running to some wires connecting to a plug at the fire wall where the wiper motor is! there are something like 8-10 wires running into it, different colours, do you have anything like this with your wiring?

i'm starting to think i have a mr or hr30 made to look like a rsx! the front disks are only 256mm across and theres no powersteering?? all your info has made me think??

brilliant thats great info, i'm running slotted dba rotors on the front and standard on the rear with bendix comp x pads, no problems stopping, that post i put up was an idea i had but i'll put in the don't bother pile and think up something else!!

i just picked up a tower brace today $140 for a CUSCO hr30 brace in the same blue, was waiting for whiteline to make them but found this one instead!

i've been thinking of something to look into, feel free to put a stop to it with any hints, Ok dr30 front rotors with custom mounting brackets for the r or z 32 front calipers but transfer mr30 or hr30 front rotors and the larger calipers to the rear end, any thoughts!

well done, sounds like a bute!! did you give up on trying to find the tail lights and find yourself a whole new car instead??