Jump to content
SAU Community

Recommended Posts

Well, this is new to me. a new forum topic. hope it doesn't get snowed under...

I just picked up my 1990 gts-4 from compliance (in Melbourne). Nice, started straight away.

Drove round the corner to put in 20L of fuel... Again, no problem starting.

Got home and couldn't re-start the thing.

It had plenty of time to cool down (if its not on boost, there is no need to leave it running to cool the turbo, right?)

Occasionally it will briefly (1/2 a second) tick over, but then it dies.

It has been suggested to me that it is fuel starvation. Fuel filter is top of the "I can do it" list. Mechanic is second (and an RWC). Is there any way I can check it? Or are there any other ideas / theories?

I just don't get why it worked before and not now. Talk about deflating expectations

And yes, I tried the search button. 'search flooding', according to the server. I don't get it - I am sure that I have seen these type of posts many a time before. Oh well, If I have transgressed, I am sure I will be told.

Link to comment
https://www.sau.com.au/forums/topic/100047-rb20det-wont-start/
Share on other sites

when it doesn't start what are the symptoms you see/hear?

do the lights go dim? does it cough and splutter?

does it tound like it wants to start but simply doesnt?

do you hear the fuel pump prime when u turn to acc and on?

starter mortor turns over

most of the time nothing, and then it will splutter for a second and die.

to me it sounds like it wants to start

I can hear the fuel pump prime when I turn the ignition on

One of the warning lights comes on -

S S S

_____

== ===

-----

left of the 'open door' light, and under the '4wd' light. I don't know what it is, and it *may* be relevant.

I get off at 2 today (home at 3), so I'll be checking it out then.

thanks

Edited by ebola

You dont have an alarm do you? My parents SS did the same thing.. would start, die, start, die.

Disconnected the battery and it worked fine after that, though it was the imoboliser doing it. Maybe check all your fuses.... thats where i'd start, then the obvious filters, etc.

Dayne

My car has no alarm, and I had already checked the fuses.

Your suggestion about the filters is close though.

The airbox was hardly connected to the turbo intake. Check the filter, knock the pipe off, engine wont start, post on SAU, look dumb, re-connect hose, clamp the thing on PROPERLEY, smooth as anything.

First bit of fun with my new car. Woo Hoo!!!!

Thanks for the suggestions though, all filed away for future reference.

you got spark right? if not id say igntion module... memba ur car needs three things.. spark air fuel.... fuel, could be ur fuel reg

spark.. make sure ur CAS is connected correctly. manual or auto?

need to give us more info dude

My car has no alarm, and I had already checked the fuses.

Your suggestion about the filters is close though.

The airbox was hardly connected to the turbo intake. Check the filter, knock the pipe off, engine wont start, post on SAU, look dumb, re-connect hose, clamp the thing on PROPERLEY, smooth as anything.

First bit of fun with my new car. Woo Hoo!!!!

Thanks for the suggestions though, all filed away for future reference.

you got spark right? if not id say igntion module... memba ur car needs three things.. spark air fuel.... fuel, could be ur fuel reg

spark.. make sure ur CAS is connected correctly. manual or auto?

need to give us more info dude

I meant that I got my car working. Though as usual, my statements are as clear as mud.

spark, air and fuel.

could smell the fuel (so there was some), and the fact that it would splutter for a second or two implied ignition (and compression).

I had forgotten about air.

I had checked the paper element in the air filter (needs replacing, but not urgently), and it seems the hose clamp wasn't on properly. The hose had come off the airbox. I guess I'm lucky it stayed put driving it home.

Because there was no air flow through the MAF sensor, it wasn't starting. I guess when it went for 1/2 a second the vibration of the motor being turned made it line up briefly.

Its a manual, and as it was a simple *stupid* thing, I have not taken the CAS module off to check it. RWC, rego, THEN I get to play.

Again, thanks to the people on the forum for helping.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...