Jump to content
SAU Community

Bleeding Hicas

twisted

By twisted,
in General Maintenance

 Share

Recommended Posts

twisted Enthusiast

twisted

Posted
Posted

Just wondering on how to bleed the hicas on r32 gts-t. Just changed the power steering fluid, and bled the system by jacking the car up, and running the steering through slowly, but when I went for a drive the hicas is very twitchy now when driving in a straight line at 80kmh. Will it bleed itself over time (as hicas does not opperate constantly like power steering? Never used to be twitchy like this. Any help greatly appreciated.

Link to comment
https://www.sau.com.au/forums/topic/100123-bleeding-hicas/
Share on other sites
luckydip Enthusiast

luckydip

Posted
Posted (edited)

I think there are 2 bleed nipples on rear rack. Might be worth a try as there could be an air lock in the system somewhere? When I replaced a pump recently - basically total system (front) had to be primed and everything was ok in rear before and after that.

But in long term, I agree with Josh.....

Edited by luckydip
Link to comment
https://www.sau.com.au/forums/topic/100123-bleeding-hicas/#findComment-1826067
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      New R32 owner soon

      By joshuaho96 · Posted

      Hard to say, just pop the rocker covers off and have a look if you think it's cammed. You probably need to replace the valve cover gasket/half moons anyways.
    • niZmO_Man
      R32 Nostalgia

      By niZmO_Man · Posted

      From my youth: GTi-R clutch change is a massive pain. The gearboxes are fragile? But the car is super cool and I want one 😢 
    • niZmO_Man
      New R32 owner soon

      By niZmO_Man · Posted

      Remember this is 1988 tech.
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Driveline vibration is resolved. I ended up loosening all my engine mount and trans mount bolts, giving it a good shake then retightening everything and it's gone... Let's just say I was surprised that fixed it.  I've been happily driving it around again but unfortunately put zero time into my direct port/constant pressure WMI setup. I'm on vacation next week, so I'll try and finalize it then.  On a different note, I spent all week fuel/ignition mapping 2x 216L V16 engines. Turbo's were burning glycol and we swapped them out for larger units. We also had planned emissions testing on site, so I figured I'd be there the same week to use their instrumentation and massage any emissions issues out if needed. This was a first for me. Fuel management is similar in certain ways to automotive (i.e air density as load variable) but very different in others. It's all PLC based and AFR's are controlled by air and not fuel. They use a control valve between the turbo and air manifold to control pressure which in turn controls AFR's. Due to this, target AFR tables supplied by the OEM are in pressures and not mass which really through me off. They use air pressure vs fuel pressure tables. I also relied on an O2 concentration sensor the emissions team had in the exhaust. Ignition timing was also all over the place and we were losing a fair bit of power. They're now happily sitting at 16-40BTDC depending on load. We were making about 1600kw at 900rpm at 90% load. Engines were running a lot smoother as well.    
    • Duncan
      1992 R32 GT-R Race Car

      By Duncan · Posted

      heh, aint no R32 ever meeting modern targa cage rules unless the driver is veeeery short OP, good luck with the sale, since its already in the land of freedom I'm sure you will find a good buyer.
×
×
  • Create New...