Jump to content
SAU Community

Recommended Posts

i was wondering if anyone else has this problem... when ever im on boost and i go over a bump in the road my rear wheels will bounce but un evenly and it cuases alot of shakes noise and discumfort not to mention the car doesnt like it much either

i was thinking it might have something to do with my LSD or rear suspention not sticking the wheels to the floor hard enough ..

please help

Link to comment
https://www.sau.com.au/forums/topic/100744-rear-wheels-tramping/
Share on other sites

Shock absorbers control the vertical movement of the wheels after the spring has been compressed (by a bump). What condition are the shocks in? You could try the old bounce test, push down on one side of the rear 4 or 5 times rapidly, and then release. It should retun to normal height without bouncing again. If it bounces its new shock absorber time. I would check the front as well, if the rear is stuffed, chances are the front is too.

If the bounce test looks OK, then my next guess would be rear subframe bushes. Have a quick look around the 4 bushes, marked in the following picture with the green dots;

R34_GT_R_Rear_Suspension.jpg

What you are looking for is signs of leaking silicone, sticky goo and split or torn rubber.

Hope that was of some help

:D cheers :D

Edited by Sydneykid

Yeh ive done the bounce test b4 and that is fine .... im at work at the moment so i cant go n look at the bushes. my cars gett8ng close to 100kms im thinking that you may be right .. i just changed the front control arms ball joins were gone maybe its time to change all thebushes aswell

Also another thing .. this only happend if im excellerating over the bumps if i roll over then no matter the speed its fine

The tyres are transmitting the acceleration and twisting torque, shocks and bushes are both relied on to hold the torque.

:D cheers :D

i took my car out for a hard thrash last night and doticed that my car is tramping a lot more now. But ive noticed a little clicking noise now, when i ease off the clutch i can hear a clicking noise coming from the rear, its like with each revolution the wheels do it clicks. (the sound is kinda like if you have a rock stuck in you treds... but there is no rock in my treads) would this be related to anything i have been worrying about.

please if someone could help me ... if i were to take my car to a suspention specialist like Heasman at Tempe would i get charged an arm n leg for them to change my bushes or should i figure out how to do it myself

i took my car out for a hard thrash last night and doticed that my car is tramping a lot more now. But ive noticed a little clicking noise now, when i ease off the clutch i can hear a clicking noise coming from the rear, its like with each revolution the wheels do it clicks. (the sound is kinda like if you have a rock stuck in you treds... but there is no rock in my treads) would this be related to anything i have been worrying about.

please if someone could help me ... if i were to take my car to a suspention specialist like Heasman at Tempe would i get charged an arm n leg for them to change my bushes or should i figure out how to do it myself

Get a quote

:rofl: cheers :rofl:

Do the pineapples provide enough reinforcement to hold the subframe if the origional bushes are or even worse WERE leaking.

Mine tramps like nothing on earth, on the dyno standing next to the car I could see the left rear wheel and subframe attached pull forward.

I'm about to throw a set of bushes through the front and sort out the subframe bushes, Sk you will receive a PM shortly. :P

Noltec do subframe bushes for the R32's, they can be had from UAS for ~$190, but as mentioned are a pain in the arse to get out for the usual home mechanic.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
    • OK, so a bunch of trim needs to come off to get to the rear shock top mounts. Once the seat is out of the way, the plastic trim needs to come off. Remove 2 clips at the top then slide the trim towards the centre of the car to clear the lower clip Next you need to be able to lift the parcel shelf, which means you need to remove the mid dark trim around the door, and then the upper light trim above the parcel shelf. The mid trim has a clip in the middle to remove first, then lift the lowest trim off the top of the mid trim (unclips). At the top there is a hidden clip on the inner side to release first by pulling inwards, then the main clip releases by pulling the top towards the front of the car. The door seal comes off with the trim, just put them aside. The the lighter upper trim, this is easy to break to top clips so take it carefully. There is a hidden clip towards the bottom and another in the middle to release first by pulling inwards. Once they are out, there are 3 clips along the rear windscreen side of the panel that are hard to get under. This is what the rear of the panel looks like to assist:
×
×
  • Create New...