Jump to content
SAU Community

Recommended Posts

Got my car back this afternoon from the mechanic. He didnt change the afm, basically gave it a check over, put it on the dyno, drove it round on the road a bit and said he couldnt fault it. Got it back on the highway and within 5 mins i had created a traffic jam! The problem is very easy to instigate, if i drive it gently and not on boost, all seems ok, if i give it some, say 1/2 bar or more, after i stop accelerating it basically looses all power, splutters, shudders i get very little response form the accelerator (if any) and if i fully remove my foot from the gas it will stall but i can keep it alive by pumping the accelerator, eventally it springs back into life as if nothing happeded. If i accelerate hard again same thing happens. Any ideas??

Cheers

Twitchy,

Sounds similar to a problem I had (and which we eventually fixed). Car would run like a dream and then, for no apparent reason, loose all power, survive a complete stall by pumping the accelerator, then after about 15-20 seconds, it would come good again and off we go. Kept happening at the most inappropriate times.

Same deal, we thought AFM, replace both (paid about $150 each second hand). No good. Changed fuel pump, checked wiring, relays, computer, CAS, spark advancer - basically everything you could think of. Mechanic would say - "I think we've got it now" after they road and dyno test - only to do it again on the way back to work.

ANYWAY... turned out to be the plug to the computer. It has a single bolt on the centre of the plug. As the car accelerates or brakes, the plug would rock - ever so slightly - and lose connection with the fuel pump pins. Used a bunch of zip ties to hold the plug firm on the edges - never had a problem since.

It's a long shot - but if it is the cause - you may not have thought to look at it.

Hope you get it fixed soon.

Cheers

Peter

ANYWAY... turned out to be the plug to the computer. It has a single bolt on the centre of the plug. As the car accelerates or brakes, the plug would rock - ever so slightly - and lose connection with the fuel pump pins.

Hi Peter;

that's a beauty, how did you manage to find it?

GTR 32,

I think it was when they were changing over the ECU (from Apexi back to stock back to Apexi) when they noticed the plug - which is actually more like a bar had a slight bow in it. I would have been stuffed otherwise - it had taken 3 weeks of trial and error, calling in auto electricians, 2 fuel pumps, etc, etc, etc when someone came across this.

At one stage, whilst at the mechanics, we couldn't start the car. Put a pressure gauge onto the fuel line and had zero pressure. Everyone stuffed around trying to work out why - no go. One of the guys leant up against the car - hey presto, full pressure.

Was driving us nuts.

Definitly worth a check if you experience any wierd stalling as described.

G'day Peter, very interesting reading your reply, sounds almost identical to my problem. I havnt heard back from the mechanic since i gave the car back to him last week (wednesday) so i gather he hasnt fixed it. First thing tomorrow i will ring him and let him know about your problem and solution. I have a feeling that it is an electrics problem due to some other strange things (electrical) that have happened in the past...he's not so sure though. I really appreciate your advice and will be sure to let you know the out come.

Cheers

Andrew

I didnt realise how lost i would feel without my car :rofl: i usually walk around with a big grin on my face, however since that fateful day last week i seemed to have lost such an expression :) (never thought i would feel like this about a car).

Edited by Twitchy
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...