Jump to content
SAU Community

How To Take Off Factory Steering Wheel

Sammie

By Sammie,
in Exterior & Interior Styling

 Share

Recommended Posts

Sammie Proficient

Sammie

Posted
Posted

im trying to take off the factory steering wheel in my s1 33 gtst ive taken off the main bolt what do i have to do next ive tried pulling on it and wiggling it a bit but no luck and this is the first time for me any help would be great trying to do it right now

Medium Dave Proficient

Medium Dave

Posted
Posted

MacGuyver is right, track down one of these steering wheel puller's, I think it is possible to do damage to the collapsable steering colums if you dont -Disclamer on that last statement: not completely sure, something someone told me once years ago, could be wrong, i dunno, but why take the risk?

MacGuyver Mentor

MacGuyver

Posted
Posted

Yeah I've heard of damaging the collapsable steering columns as well. You should be able to get a steering wheel puller from somewhere like Repco or Super Cheaps, doesn't cost much. Don't try to remove it with out one! And make sure that when you do remove it, the front wheels are straight so when you put the new wheel/old wheel back everything is straight again.

"My cat's name is Mittens."

blind_elk Grand Master

blind_elk

Posted
Posted

You can usually get them loose by grabbing the wheel at "quarter to three" and wiggling back and forth (along the axis of the steering column, not like you are turning a corner) at the same time as pulling the wheel towards you.

It is probably a good idea to leave the nut on a few threads to avoid belting yourself in the forehead when it finally gives.

Rednisr31 Community Regular

Rednisr31

Posted
Posted
You can usually get them loose by grabbing the wheel at "quarter to three" and wiggling back and forth (along the axis of the steering column, not like you are turning a corner) at the same time as pulling the wheel towards you.

It is probably a good idea to leave the nut on a few threads to avoid belting yourself in the forehead when it finally gives.

i have an r31

i took a stock wheel off on wednesday

i used a hammer and left the bolt on as you would want to instead of copping a steering wheel to the face

Lazy-Bastard Grand Master

Lazy-Bastard

Posted
Posted

Steering wheel puller

Either side of the centre nut that holds the wheel on there will be 2 threaded holes (one either side).

The puller kits come a main piece shaped like so =0=, There will be a large bolt that goes through the centre of the puller and butts up to the bolt that holds the steering wheel on. Also in the kit will be a range of bolts to fit different thread sizes for the 2 threaded holes on the sides that I mentioned before.

Just screw the two side bolts in so there is a decent amount of thread holding them in and then screw the large centre bolt in until the wheel pops off.....5 minute job.

sidewazegtst Collaborator

sidewazegtst

Posted
Posted

Hey man what's up.

If your planning on using an aftermarket wheel and hub, let me know how it all went together please. Mainly how easy it was to make the horn work b/c I'll be doing the same thing on my car soon.

Thanks a lot.

Cheers B)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
    • Robot
      Skyline v36 350GT sedan hunting on idle

      By Robot · Posted

      Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...