Jump to content
SAU Community

Recommended Posts

Hey guys,

I have recently set a power goal of 200 rwkw for my RB20DET R32. At the moment I have between 160rwkw and 170rwkw. The mods I have are:

3inch Exhaust

ZG30 Turbo

Boost controller running 12 - 14 psi

No A/M ECU yet. Looking at the Power FC.

Besides from a FMIC, what mods should I look at for squeezing out an extra 40kw at the wheels?

Link to comment
https://www.sau.com.au/forums/topic/101782-200rwkw/
Share on other sites

remapped ecu, good cold air intake, fuel pump, 3" split dump and get it tuned. i dont think you will make 200 however

What paulr33 said.

#But your 3'' xorst will still be ok as long as it is 3'' from the turbo back.

#Hi flow air filter.

#Remapped ecus are allright.But if you have the money get a pfc.

#Maybee a adj fpr.Becuase at high injector duty you will want constant high pressure in teh fuel rail.I was told this by CRD.

#A hi flow rb20 or 25 turbo and you will make over 200rwkw.

Other than that teh stock turbo wont push beyond 180-190rwkw that easily.You do need all of these,though,if you want to get the max! out of your current setup.You need an upgrade on the turbo.

As you would have allready seen though dynos are conservative to say the least.With many saying their car has 200+rwkw on the stock turbo.When i was at CRD my r33 was tuned to 182rwkw stock turbo with a 2.75'' dump,stock cat and 3.5'' xorst from then on.With all the usual other mods.

I hope your not running 14psi in the heat of the day with that tiny intercooler.After the powah look at the suspension if you havent allready.Then take it to the track and thrash it!!

I am at the point now where i can upgrade the turbo and easily make 220rwkw.

HTH... ;)

Link to comment
https://www.sau.com.au/forums/topic/101782-200rwkw/#findComment-1866474
Share on other sites

Ill also get it tuned on Shell Optimax Extreme and see how that goes.

Is that the 100ron stuff? If so i heard it wasnt good for skylines, apparently it only works well in new cars.

I havent tried it though, i just stick with my BP Ultimate.

Link to comment
https://www.sau.com.au/forums/topic/101782-200rwkw/#findComment-1867113
Share on other sites

  • 2 weeks later...

Just an update. I have installed a FMIC and an apex'i power intake. It actually made alot more of a difference than I expected it to! Its alot louder now too:). I am almost ready to order a PowerFC for it. Any suggestions where the best place for one is?

Link to comment
https://www.sau.com.au/forums/topic/101782-200rwkw/#findComment-1904055
Share on other sites

hey dude, ive got a 4dr 32 aswell and i made 170rwkw with rb25 turbo, gtr fuel pump, 1bar boost, 3" turbo back exhaust, and shitty hks mushroom pod

no front mount... its on the way though and itll be in the car soon

my point is... get an aftermarket dump pipe!

they do HEAPS

go look at your stocker and youll see that the bit where the wastegate opens goes into a "wall" in the dump pipe... VERY bad design, causes a SH*TLOAD of turbulance when the wastegate opens and makes exhaust gases flow really sh*tty.

also, i assume that by ZG30 turbo, you meant VG30 out of a 300ZX.

if this is the case, go get that hi-flowed.

many people have had good results with hi-flowing that turbo because of its decently large exhaust housing

PS: GET THAT DUMP PIPE!!!

Edited by salad
Link to comment
https://www.sau.com.au/forums/topic/101782-200rwkw/#findComment-1904961
Share on other sites

You may want to figure if the VG30 turbo you have is the steel wheeled version. As you should be able to run 18+psi fairly reliably. And with other sensible mods Such as a Good quality split front/dump, Quality cat (a metal one), GT-R injectors, Regulator and PFC or remap there is no reason why you can't comfortably surpass the 200rwkw figure.

Oh and finding a PFC for a 32 can be difficult. "AP Engineering" make em.. don't know why.

This is why so many 32 owners opt for the remap instead. Wich can net very healthy results if performed correctly.

Good luck anyway :P

Edited by Drift_Limo
Link to comment
https://www.sau.com.au/forums/topic/101782-200rwkw/#findComment-1905506
Share on other sites

sure r u? have you driven one? big call if you havent.

imo most remaps are just stock tune with fc and speed limiter removed

a remaped ecu(tune by Adelaides Guru) and just a stock wt fcd comp were both tested out on Huddys car both power curves were exactly the same?

oh and VG30 turbo's never came with steel rear wheel from the factory.

Edited by 1400r
Link to comment
https://www.sau.com.au/forums/topic/101782-200rwkw/#findComment-1907651
Share on other sites

AS everyone else has mentioned:

FMIC (which you have now)

Apexi air filter (whic you have now)

3" dump all the way through (with a "CUSTOM" cat :D )

PFC is the way to go if you can afford it but there is nothing wrong with getting a ECU remap by someone like Dr Drift, Sams results kinda speak for themselves!!!!

If you want info on the "CHEAPEST" AP Engineered Power FC then PM :)

Other than that good luck with your power figure and hope you get what your looking for...

Cheers B

Link to comment
https://www.sau.com.au/forums/topic/101782-200rwkw/#findComment-1907776
Share on other sites

check out huddys thread in the ceffy section

mods needed

fuel pump

exhaust

fcd

2530 or similar

front mount

boost required 1 bar

result 215 rwkw

That sounds like alot, I have fuel pump, 3inch exhaust/dump pipe, gtr injectors, wolf 3d, cooler, and 1bar and Im making 160rwkw, altho my turbo is still stock.

Link to comment
https://www.sau.com.au/forums/topic/101782-200rwkw/#findComment-1910154
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
×
×
  • Create New...