Jump to content
SAU Community

Recommended Posts

  • Replies 51
  • Created
  • Last Reply

Top Posters In This Topic

How long does it take to recieve the appropriat cams licence.  Also where is a good place to put the fire extinisher?

You can get it on the day if need be but i would get it before hand.

Allow about 2 weeks but u will have your temporary one anyone if it doen'st trun up :P

yep, can get it on the day, nice to have it all sorted b4 hand though.

thinking of asking my old man if i can run the clubman :P will be on for donkey kong greg :P

EDIT: Savman, fire extinguisher has to be mounted SECURELY within reach from the drivers seat, ie. under your seat or something. has to be at least 900g dry chemical type (a red one) on a metal bracket.

Edited by bj_dove
yep, can get it on the day, nice to have it all sorted b4 hand though.

thinking of asking my old man if i can run the clubman :P will be on for donkey kong greg :P

EDIT: Savman, fire extinguisher has to be mounted SECURELY within reach from the drivers seat, ie. under your seat or something. has to be at least 900g dry chemical type (a red one) on a metal bracket.

Is that it for safety requirments? So rock up on the day, pay for your licence and screw a fire extinguisher to the floor? Cool.

XRATED - You'll need a battery locating sticker too. Just a blue triangle cut out of book covering 'contact' would do.

BOV - Thats soft! Your GTR would be awesome on that course.

Getting into the 49s is the plan this year.

BJ,

I picked up a Quaife the other day. So will try to have that installed. Also did a set of stainless tuned pipes and 2.75 in system. I think its pumping a little harder now - but still gotta get it around that bloody bend eh? :)

PS: Stu I know Im soft but Im gunna have to wait until I scratch it first and it dont matter after that. Once the Mrs runs the mags into the curb I'll be right :D

Cheers

Have been helping a mate import an nice black R32 GTSt. We just picked it up from the docks & seeing it's as good as we though it would be hes giving it a tidy up this weekend and should be running the Hillclimb.

  • 2 weeks later...
Have been helping a mate import an nice black R32 GTSt. We just picked it up from the docks & seeing it's as good as we though it would be hes giving it a tidy up this weekend and should be running the Hillclimb.

thought my ears where burning!! hi stu and everyone else. yes, fixing up the bodywork, not much to it since dad's good at that sort of thing (im hopeless)

took the car out to baskerville yesterday to see what ive got to play with. i dont think i was driving it correctly, i also wasnt thrashing it either. just wanted to give it abit but was breaking fairly early for the corners. had to remember which way the track went (haha). its been over ten years since i had a blast. was doing 1.15's i think. i didnt have stop watch, only the dash clock and then counting after it clicked over a minute. heal/toeing was a bitch too.

front brakes started to warp so i gave it away for the day.

ive found this site which some tunning tips that might be of use for people.

http://www.rb20det.com/tuningguide.html

hope to be at the hillclimb but ive just lost my job so it will make thing diff for a little while till i find another (let me know people if you know of any jobs going)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
    • To drain the Intake Heat Exchanger, there is a crappy drain plug in front of the driver's side front tyre: You should use the largest headed phillips screwdriver you had, and in my case I needed vice grips on the hose above as the plug was tight (tighter than it needed to be, since it has an o-ring seal).  After you have a tray down and open the drain, open the intake heat exchanger reservoir cap (drivers side one) and you should get a couple of litres of coolant To get to the radiator, you need to remove the plastic engine undertray. It is held on with a series of 10mm headed bolts and some clips. For the radiator, there is another type of crappy drain (kind of like a plastic banjo bolt) and you should attach a length of hose to direct the stream of coolant per this pic (otherwise the coolant hits the rad support and goes everywhere). The drain is on the rear of the radiator on the driver's side and a bit hard to find. Put a big tray or bucket down (5l won't be enough) and slowly unscrew the fitting by hand. You only want to remove it far enough for coolant to flow, it you unscrew it right out the whole fitting and direction pipe will come off and you will get a coolant bath (yum!). Undo the radiator reservoir cap and it should empty about 8l
    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You also need to drain the intake heat exchanger to remove the radiator so you will need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. 2 other tools that really help dealing with coolant lines and spring clamps are Bent Needle Nose pliers Hose pliers Between them they will reduce the frustration (and injury) potential by about 1000% Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
×
×
  • Create New...