Jump to content
SAU Community

Recommended Posts

NARDI,

I've let the group buy go until the end of Jan... Couple more days left. :angry:

There's actually been more interest that I expected.

Monday I will PM every one with my bank details and have them deposit money. :(

  • Replies 134
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Am I to late for this?? I just found it and really need one of these with a plug, have cash ready can you give me a price sent to melb!!

Cheers

JL

Edited by JL

On wednesday I will pm every one with bank details and my personal details for your piece of mind.

I will also request that you let me know if you want an afm plug or not. Then deposit the required coin as you say. :P

No point buying a plug as with postage you can get it for the same price if you head down to your local auto shop.

They retail around $17-$18. I can get them for $10.70.

I know it has probably been said before but the plug will have to be rewired, is that right? And if the mesh is in both ends do we pull the turbo end out?

I've left the mesh in mine.. Its been known to cause idle issues without. :D

The afm plug does have to be wired in to the afm section of the loom, or more so simply cut and recrimp.

I did remove the mesh on my stock afm, I swear I noticed a slight spool time decrease. BUT I had slight idle issues. :D

Count me in.My meter is maxed out at 230rwkw`s.One question though, does Advan supply a plug that just plugs in? I think it was around $50.

Unsure on the advan 'plug-ins'

The only way I can see it happeneing is if they have made up a male plug that plugs in to the exisiting std plug that then is wired in to the Z32's female plug that plugs in to the z32 afm.

Either way wiring or crimping. :P in to the loom is very easy, from memory the pin out is the same, so simply chop and attach from left to right. Providing its the R32/R33 S1 4pin type.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...