Jump to content
SAU Community

Recommended Posts

Hey people

I recently got a set of 19 x 8 inch rims on my R34. Now the tyres are 235/35/19 all round, and have an offset of +35 which is the same as stock. The wheels were balanced etc, but when they were put on it was discovered that a 2mm spacer was required for clearence of the front brakes due to the shape of the spokes and big ass R34 front brakes. I also put them on the rear just so all was even. I have now found that at speeds over 100kmph a get a shake in the wheel, sometimes it is only slight, other times it is pretty violent.

Do you think that becasue the wheels/tyres were balance for the +35 offset, that with the spacer bringing it down to +33 the balance is out of wack and is causing the shakes. Should i get them rebalanced and get the tyre place to attach the spacer to the machine when they balance them?

As a side note, i have not had a wheel alignment since i have had the new wheels put on, could this be causing the problem?

Any advice would be great.

Link to comment
https://www.sau.com.au/forums/topic/102086-steering-shake-with-new-rims/
Share on other sites

Alignment doesn't affect or cause the shimmy mxtcy is experiencing.

I suspect it's a result of the spacers not having the studs properly centred. Most rims these days actually centre on the hub, rather than relying on the wheel studs to centre the wheel on the axle.

  • 3 weeks later...
wheels are buckled??

cost around $60 each to get them rolled if they are

find a tyre shop that does ON CAR balancing.

that way they balance the whole assembly, works great.

but if you remove your wheels later on make sure mark them to fit them in exactly the same spot on the hub.

cheers Russell

I would go with spacers as the culprit. I had "slip on" spacers when I purchased the car and had a very violent vibration at 80km/h.

Got all 4 wheels aligned and balanced to no avail.

A tyre shop told me the spacers was the issue and I removed them and replaced them with spacers that had a wheel locater on them.

Reduced the vibration by 80%. But I will remember to get the wheels balanced next time with the spacers and see what happens.

In saying all that, mxtcy as you only have a 2mm spacer I would get rid of them and machine 2mm of the caliper.

yeah spacers arn't they suposed to tie the spacers on when the balence them to get it right it happen on my friends r33 they balenced the rims and just slapped the spacers on it shook like all buggery at 100kmph dodgey tyre factory!!(TTF) spacers are dodgey anyways!

when i put my stockies back on my car. i didnt know my 19s had a little plastic ring that sat next to the hub and inside of the bolt holes on the wheel, mechanic called them "locators"... anyways, i bolted my stockie on tight! and drove it on the highway, and then to vicroads (clear a defect :rolleyes:) leaving vicroads, i noticed a wobble, pulled over, and i could nearly shake my wheel off, nuts pretty much just fell out... scarey shit, lucky i noticed it before i got back on the highway...

so with that in mind, spacers with highspeed, heavy brakeing and sideways... i'll leave my wheel 3mm closer to the car!

Locator rings are actually a very good thing as they locate the wheel onto the centre of the hub, stoping shaking etc. and they aren't 3mm or anything like that, infact they don't sit out any further than the inside bore of the wheel itself. All hi quality wheels come with metal locators on them. The spacer i'm getting made up are hubcentric. Thus the spacer centres on the hub perfectly and then bolts on. the wheel then locators on the centere of the spacer hub using the biult in locators ring. and woot no more shaking.

I have same problem I bought new wheels last thurs from ozzy tyres and same thing!!! where can I buy hub adapters??? And are they legal?? I'm mid way through trying to get them to rectify my problem as its their fault for not telling me. But their no longer returning my calls!!

hey mxtcy

what i meant, the locator, which was made for my 19's stayed on, so when i put my stock wheel on... the wheel never huged the hub properly.

i was just comparing that to spacers which would be 'long term'.

however i know of people with spacers, that even drift on them no probs... unfortunatly i can't afford to take the risk

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
×
×
  • Create New...