Jump to content
SAU Community

Recommended Posts

  • Replies 717
  • Created
  • Last Reply

Top Posters In This Topic

Im actually super keen for this!! The later the better (late March) as need to get a couple of things fixed 1st on the Cefiro.....

yes it aint a Skyline but we all can't be cool and own a Cefiro :D

Ando

ill bolt std turbo's on "twoogle" to enter STD turbo GTR.....lets see how far they can be pushed....starting a small donation fund to pay for some stockers......

Edited by DiRTgarage

Well if you put the 2530's back on you would most likely win the aftermarket turbo section.

You're welcome ports and deviat.

Fixed the first post with the typo. 10% of all punches thrown on the day will be to 2rismo :D.

This looks like being huge guys. Firming up for the 11th.

There will be prizes for each category of:

Stock Turbo R32 GTST

Aftermarket Turbo R32 GTST

Stock Turbo R32 GTR

Aftermarket Turbo R33 GTST

Stock Turbo R33 GTR

Aftermarket Turbo R34 GTT

Stock Turbo R34 GTR

Wtf Adam? no Stock Turbo R33 GTST???

dohh...

booo...

To quote UAS directly:

We check the vehicle out before going on dyno including fluids etc and adjust tyre pressures for accurate reading. Will diagnose and advise on cars performance and anything we discover and at least two runs check boost, torque, power and air fuel ratio with a pic of car dyno print out and if they bring their own floppy disc we can supply digital version. ( If they forget we have floppy and can email it to them).

There is a good lunch shop which will be open until at least 12 although can stay open longer pending demand. Our shop will be open also and 10% minimum discount for SAU dyno day. Also our workshop for before and after mods to check on dyno pending demand for workshop and dyno numbers.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Well, this is probably where a wiring diagram and a multimeter come into play.
    • I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia front end... *Edit: On closer inspection the test car still had the R32 body, but only the front end had Silvia panels etc.
×
×
  • Create New...