Jump to content
SAU Community

Recommended Posts

ok guys time for a change..

car is as follows..

1995 gtst, last of the series 1..

63,000km

full suspension setup including tein ha's,

and complete whiteline kit

600x300x100 fmic with chrome piping

heavy duty clutch

full professional respray to yellow including new window seals and sprayed under bonnet, got gtr rear wing, gtr front bar and side skirts

el blue/green dash lights

dual stage boost controller

3inch dump and tanabe cat back exhaust

K and N air filter

turbosmart type 3 BOV

full bride racing seat replacing drivers seat

ive also got a power fc sitting in my room which is ready to be installed and a hks super dragger exhaust with a 3inch cat sitting in my garage.. if u wanted to swap exhausts

umm think thats about it on the car.. with power fc installed and tuned i think 190rwkw on approx 12 psi should be possible with her..

$27,500

im sure if anyone was buying a car they could figure out how much ive spent on the car.. no stupid offers please

Link to comment
https://www.sau.com.au/forums/topic/10362-yellow-33-gtst-for-sale/
Share on other sites

i only just decided to sell this week.. im not in a huge huge rush to sell her.. ive put alot of time and $$$$ into the car....

i thought about putting some rims on her but decided not to.. i like the more jap style drift rims which most ppl dont like.. adn 16inch rubber is cheap too.. rims arnt that expensive.. whoever buys it can put what they like on it..

and to all those ppl asking for me to seperate parts off her..im going to try to sell it off as one for a while and if that doesnt work.. im gonna strip her back to near stock and sell of all the bits.. chances are i would most prob make more money that way but im a lazy ass and would rather sell it without the hassle...

thats fair enough :D

i too like the drift style rims :) well i'm basically waiting on my insurance money to come through since some fool ran into me.. so once i get that i'm in the market for an r33, and yours seems like it has hte goods and the looks what i'm after. I'll watch the thread and if it sells it sells if not , u have one keen buyer here when the time comes. :)

later

mark

mark ill try to get some photos for u this week sometime..

damm i need to invest in a digital camera..

Originally posted by qikshift

can't wait to see em ;) mmm bride seat :) if you still ahve the car i'll prob make the trip to nsw when my insurance shit comes through :) very impressed ...

thats if u still have it or course :)

mark

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...