Jump to content
SAU Community

Fs: Mazda 13bt Hb 2dr Fully Engineered [syd]

buz138

By buz138,
in For Sale (Private Whole cars only)

 Share

Recommended Posts

buz138 Enthusiast

buz138

Posted
Posted

For sale: 1982 Mazda HB 13BT

Item Condition: paint is average for age but body is 90% straight. Engine is a low km import S4 with 100psi compression in each rotor as tested a couple of weeks ago. I have replace every single gasket on this motor and stipped it down to bare block and cleaned it before it was fitted just 3 weeks ago.

Just had a custom exhaust made with custom turbo manifold to sit it foward and higher, 2.5inch custom dump into hi-flow cat and a drift style angled cannon at rear.

It's running a Microtech MT4 with carbon fibre 4 line handset that is currently being tuned with a S2 RX7 dizzy. Still running standard topmount cooler with S2 frontmount oil cooler and S3 3 core radiator with 14inch thermo controlled by the Microtech.

Fuel system consists of a Bosch VLT pump fed by a holly blue pre-pump and custom surge tank. Just fitted an ARC blow-off-valve for more of a jap sound and has a few jap gauges and Nardi drift wheel.

Has climate control (but no A/C) with all power windows, interior is in good condition and is very luxurious with plush seats and marble inserts around gear stick and controls. Also has lazy eye kit! :D:(:D

5 months rego, Fully engineered bumper to bumper!!!!!

New stuff less than 50km:

New bosch coils

Leads

Plugs

Exhaust

HD clutch

Lightened flywheel

All oils and fluids

New OMP race harness

Turbo Manifold

Whole new fuel system

New carbon fibre MT handset

Probably forgoten heaps so just give me a call for more info.

Should make around 160kw ATW

Price and price conditions: $7000 ono CHEAP!!!

Extra Info: Need to sell due to growing business.

Contact Details: PM, phone 0433405788, email [email protected]

Location: absolute must

Delivery & Conditions of Delivery: Can work out with buyer

Pictures:

picture30826gb.th.jpgp12230515377lf.th.jpgpicture29623ek.th.jpgpicture33926wj.th.jpgpicture35626gb.th.jpg

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      R32 Gtst - Track Car

      By Duncan · Posted

      Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • Dose Pipe Sutututu
      R32 Gtst - Track Car

      By Dose Pipe Sutututu · Posted

      https://www.facebook.com/share/p/18rmVb1SKB/ 
    • GTSBoy
      Leak from Tokico BM50 Brake Master Cylinder

      By GTSBoy · Posted

      The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • No Crust Racing
      R32 Gtst - Track Car

      By No Crust Racing · Posted

      Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • MBS206
      R32 Gtst - Track Car

      By MBS206 · Posted

      I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...