Jump to content
SAU Community

Recommended Posts

Location:Gold coast ( pimpama )

Item: R32 GTST skyline parts. Prices added :D

ad to clean up the shed so make an offer on these parts.

i can drop parts off if needed.

contact Justin ( 07 5540 7735 ) 0401-027-348

Engine ECU, to suit auto comes with plastic kick panel. (will work in a manual car)

Full set of coil packs.$ 100 Sold

RB 20 engine cover. $ 50 Sold

Complete dash loom. $ 200

Dash cluster surround with all switches $ 80

Complete stereo surround with side covers. $ 100

Glove box $30

Center ash tray $ 15

Inside & outside fuse covers.$ 10

Brake booster & mater cylinder with front discs $ 350

Origional washer bottle with motor. $ 20

Complete heater box. $ 100

Set of caster arms with good rubber bushes. $ 150

Complete set of struts with springs shocks.$ 250

Power steering resivour with lines and hoses.$ 100

windscreen wiper motor and wiper arms. $ 80

stock intercooler piping $ 100

Steering shaft uni joint.$ 10

passanger side Air vent$ 10

drivers side air vent $10

Under dash panel, goes across stering colum $10

Oil cooler $ 40

charcol canister with all lines. $20

Auto brake pedal with mount bracket $ 20

turbo Heat sheild $ 40

Air flow meter with lines and hoses that run to turbo.$ 40

Edited by just32
Link to comment
https://www.sau.com.au/forums/topic/104015-for-sale/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Working through possible solutions of converting my mechanical speedo.    Anyone know what type of speedo sensor the factory r34 gtr getrag has ? what the output is ? I assume its not a VSS and more a voltage like earlier speedo sensors ? Can an ECU read it ?  
    • roof rail delete used to be a thing, they were made locally for a while too
    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
×
×
  • Create New...